McGregNi

Joined: 31st March 2012

All Forum Comments

Topics Created Topics Contributed Forum Comments Photo Comments

All Forum Comments

McGregNi
Reading a lot of internet discussions it would be easy to gain the impression that the only important thing to worry about for your next camera upgrade is how much noise it's sensor will generate at ISO 12,800 and above ! From my point of view there's a lot more to a great camera than that, and I'm very happy that my Pentax model provides it all in spades, and at a price that the competition can't get near.

Comment by McGregNi posted on Pentax vs nikon at 14/09/2015 - 10:29

McGregNi
Good low light photography which conveys plenty of the atmosphere of the place at that time of day. The last two are my favourites for their deep contrast and the lovely blue sky tone.

Comment by McGregNi posted on Tanfield Railway Photo Evening at 13/09/2015 - 14:03

McGregNi
It sounds ignorant to advise someone to switch DSLR system based on the experience of a single model in the range. It may be that there were valid limitations with the entry level K500 which the pro felt were restrictive. In that case the sensible and logical advice should be to identify what features are desirable and tell the student to look for them in a future camera upgrade . There's no doubt that a model further up the Pentax line would provide everything that was needed.

Comment by McGregNi posted on Pentax vs nikon at 13/09/2015 - 13:28

McGregNi
Doesn't seem to make sense with them moving together. I understood the theory of it was that the 3 sliders controlled sharpening at different radius levels (as Steve said earlier) . Therefore the 3 different settings should be applied accumulatively at the processing stage. If you wanted to increase sharpening at a small radius level (fine) then you specifically don't want the sharpening at a coarser radius level increasing at the same time ....?

Comment by McGregNi posted on K3 II jpg settings at 11/09/2015 - 20:23

McGregNi
Impressive angles and perspectives! I presume you were on hill-top level to the height that the aircraft were flying over the lake?

Comment by McGregNi posted on Mach Loop Cad West at 11/09/2015 - 20:18

McGregNi
SteveLedger wrote:
I know on my K-01 and K-50, selecting Fine then changing the value also changes the Normal value to the same position on the scale (and vice-versa). I always assumed the camera only used the 'currently selected' sharpening setting. IOW: If you select normal sharpening then close the menu, normal sharpening will be used. I thought the difference was that one sharpens fine detail while the other sharpens everything. Fine Sharpness most probably decreases the radius of the operation.
I understood that each of the 3 settings (sharpening, fine 1, fine 2) were active at all times and yes, each applies to a pre-set fixed radius value (unknown to us). The fine settings remain at their centre default unless you actively open them up with the front e-dial and change them .....they are then stored and remembered for that particular custom preset (the master pre-set at the top, Natural, Bright, Portrait etc ) ...... So you end up with always 3 independent values stored, one for each slider ..... That's what I always assumed anyway.

PDCU mimics this by having all 3 sliders visible always ....(the camera interface method is just to save screen space ).

Comment by McGregNi posted on K3 II jpg settings at 10/09/2015 - 21:37

McGregNi
richandfleur wrote:
Could easily be a firmware big also...
Bad Spelling !

Comment by McGregNi posted on K3 II jpg settings at 10/09/2015 - 21:21

McGregNi
On the earlier cameras you have to use the front e-dial to access the 2 fine sharpening options, then you select each one with the 4-way controller, which then works independent of the others. Are you definitely selecting and adjusting the fine sharpening sliders directly like this? It only makes sense really if they can be individually controlled.

Comment by McGregNi posted on K3 II jpg settings at 10/09/2015 - 19:33

McGregNi
CiderDrinker wrote:
Well Park Cameras look like they are ready for it

https://www.parkcameras.com/p/5012234J/development-products/pentax/full-frame-ds...
Great price! Who said full frame needs to be expensive

Comment by McGregNi posted on Any new FF gossip at 09/09/2015 - 13:51

McGregNi
I agree that you've done a very good job .. The OOF background and the borderline around the subject are managed well technically and only the experienced pixel-peeper would find anything.

I applaud you for doing so well with Topaz Remask, which I have to admit has tested my patience beyond its limits, and I enjoy computer editing generally! It would be interesting to see how the new 'lens effects' package deals with the masking issues, which I found very difficult in ReMask. So much so I can't see myself ever bothering with it again.

You'll have to go onto YouTube and give the world a ReMask Low DOF video tutorial ! Just get yourself a baseball cap for it or people won't take you seriously

Comment by McGregNi posted on Artificial DOF - Does This Look Fake? at 09/09/2015 - 13:34

Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo