All Forum Comments
Comment by WaypointCharlie posted on I just found out. at 29/11/2015 - 13:44
I carry a push-on plastic lens cap with me and simply plop it over the eyecup - job done!
What size lens cap is it please?
I've found covering the viewfinder is essential for shots of more than a few seconds. It's not a problem with fooling the meter (I'll nearly always be using manual settings for control of long exposures) but there's a loss of contrast and spurious streaks can show up on the sensor. (To see the effect, try a shining a torch at the viewfinder during a 30 sec exposure). Whist I'm getting more methodical, too often I still forget to cover the viewfinder until I'm halfway through that award winning shot!
Comment by WaypointCharlie posted on I just found out. at 29/11/2015 - 10:58
As for forgetting to turn off the timer, you can always disable the drive mode memory via page 5 of the settings menu. The camera will then reset to single frame shooting when you turn it off. Ideally I'd like it to retain the setting for a few minutes after it's turned off, but nothing is perfect!
Comment by WaypointCharlie posted on I just found out. at 28/11/2015 - 12:51
Comment by WaypointCharlie posted on Excellent value Ballhead for a tripod / monopod at 28/11/2015 - 12:45
Comment by WaypointCharlie posted on Wanted - Uni-Loc tripod - Major System 1600 or Major System 2300 at 18/10/2015 - 22:59
I think on my previous K-5 I'd set 'Remote Control in Bulb' to Mode2, mistakenly believing Mode1 would require two presses on my cable release button.
Comment by WaypointCharlie posted on Night scene photography at 08/09/2015 - 13:54
Note when combining the self timer with exposure bracketing you'll get 3 sec breaks inserted between shots when set to 3 sec delay but no inter-shot delays when set to 10 sec.
I quite like using the IR remote but find it irritating that the camera doesn't respond to it when reviewing an image on the screen (unlike the shutter release button/cable). It doesn't work in Bulb mode so is limited to 30 secs. Setting IR remote mode is also a quick way of disabling shake reduction.
I wouldn't agonise about mirror flap on long exposures (or short for that matter). I'm not sure what sort of speeds it might be useful - 1/2 sec perhaps?
Comment by WaypointCharlie posted on Night scene photography at 08/09/2015 - 13:02

Comment by WaypointCharlie posted on Horizon correction - what are the downsides? at 06/09/2015 - 11:13
Horizon Correction - forget it. On my K5-IIs it usually seems pretty accurate for single shots but varies a bit between shots and is all over the place when it comes to bracketed (e.g. HDR) and, presumably, burst modes. Perhaps the sensor is quite sensitive to camera vibration and you should select 3 sec delays between bracketed shots. I also noticed it seemed to have difficulty if there was too much vertical tilt (even though the horizon indicator in the viewfinder was still working).
Straight-out-of-the-camera - what a waste of time. I was working at sunset with rapidly changing light conditions. I was spending too much time trying (and failing) to keep on top of exposure times and colour balance for a 10-stop filter that it left too little time on composition and taking photos. You can't use AWB with a 10-stop filter. I find that taking a manual white balance of a grey card works well, but this takes time and only works when the light isn't changing fast.
In this, not very original, example I ended up underexposed by about 1/3rd a stop, the horizon is out by about 0.1° and the colour balance and curves could do with a tweak. All things that are easy to fix PP. Visually that 0.3 stop makes a big difference, but getting the exposure spot-on in such changing light conditions is as much down to luck as skill. Of course, it's expecting a lot to get a good shot, SOOTC with a flat horizon using a 10-stopper at sunset, but for a competition you can't opt for the easy shot!

Comment by WaypointCharlie posted on Horizon correction - what are the downsides? at 06/09/2015 - 10:36
I've just taken a few shots of a still life on the tripod with a remote release with horizon correction enabled. I noticed slight differenecs in the amount of correction applied between shots. This means combining shots (as I wanted to do) requires a bit of minor post process alignment. I wonder if the camera maintains a constant correction bewteen shots when using auto exposure bracketing.
Already my feeling is to disable the horizon correction, unless taking a single shot of the sea for a SOOTC competition!
Comment by WaypointCharlie posted on Horizon correction - what are the downsides? at 28/08/2015 - 11:15


The "light through the viewfinder" problem goes all the way back to the ES, which is why the ESII has two automatic exposure mode settings, the second one puts a blind across the viewfinder. I got round this with my ME Super by shooting in manual. Of course, the mighty LX with its "off the film" metering doesn't suffer that problem.
K.