WaypointCharlie

Joined: 21st March 2012

All Forum Comments

Topics Created Topics Contributed Forum Comments Photo Comments

All Forum Comments

WaypointCharlie
Thanks RobL. Yes, that what I plan doing. For tripod mounting I find the electronic level display pretty useful, and it's more accurate than the viewfinder display (more steps). Just I've never enabled horizon correction before.

Comment by WaypointCharlie posted on Horizon correction - what are the downsides? at 27/08/2015 - 11:15

WaypointCharlie
In our case, we must submit the original JPEGs at full resolution but retitled to suit the club conventions. The competition sec. then resizes for projection. Yes, SOOTC has been a can of worms, particularly when it came to deciding whether or not in-camera post processing should be permitted. As it stands today, it has to be the JPEG produced by the camera immediately following the (single) shutter press. Potentially this means you could use Multi-exposure mode, but I think this is only possible with a single shutter press if you use burst mode, so it's not that useful really.

You can include camera processed effects (such as monochrome, even HDR), but they have to be produced at the time the shot was taken, not subsequently post-processed by the camera from the Raw file. So I've been experimenting to find the best monochrome settings for what I plan to do. At the moment I'm trying getting my head around the differences between Sharpness, Fine Sharpness and Extra Sharpness (any ideas?). Sure, it's been educational discovering the some of the features and effects the camera has to offer, but if it wasn't for the SOOTC constraint I really wouldn't find any need of them.

Comment by WaypointCharlie posted on Horizon correction - what are the downsides? at 27/08/2015 - 10:02

WaypointCharlie
Thanks David. Normally I'd be in full agreement about leaving it off, and certainly leaving off distortion correction. However, this is setting up for a straight out of the camera competition. Personally I find SOOTC a pain and it imposes unnecessary restrictions, but the vast majority of the club voted in favour of having it. Proof, if ever it were needed, that democracy is vastly overrated!

Comment by WaypointCharlie posted on Horizon correction - what are the downsides? at 27/08/2015 - 08:38

WaypointCharlie
Thanks.

0.2 degree is actually quite a lot for a sea horizon - you can bet some picky competition judge would knock off a point for it! I can manage that by eye (and with the aid of the camera's level info display page). I'm hoping the camera's sensor adjustment is better than that. Just wondered if it can degrade sharpness as shake reduction can when using a tripod (not that I've ever noticed).

I'll give it a go next week and will report back.

BTW, when enabled I notice that the level info display gives you a helpful Horizon Correction range bar (below the horizonal level bar), and the available range is narrower when Shake Reduction is on. Pentax is so nice!

Comment by WaypointCharlie posted on Horizon correction - what are the downsides? at 26/08/2015 - 21:20

WaypointCharlie
Up until now I've always run my K5 with Horizon Correction disabled. However, my camera club, in their infinite wisdom, have introduced a SOOTC competition. As I'm planning on taking a sea shot I want the horizon to be level. I'm also probably going to have to enable in-camera lens correction (yuk!) and use some Shadow Correction.

The electronic level in my camera appears to be well calibrated, so my question is, are there any downsides to having horizon correction enabled? Does it slow the camera down? Do you get any loss of sharpness? If the horizon is more than a few degrees out, does the camera give up and not attempt to apply any correction?

I'm planning a long exposure so does the correction factor set at the beginning of the shot and remain constant throughout the exposure, regardless of any camera shake?

Comment by WaypointCharlie posted on Horizon correction - what are the downsides? at 26/08/2015 - 19:39

WaypointCharlie
Actually, I've been trying out my friend's Benbo Trekker (early model, without the bendy joint in the centre column) and find it really easy and intuitive to setup. However, I guess it wouldn't be so easy wrestling with a Major 2300.

I can see why the bendy joint (with the extra head mount screw at 90 degrees) on the System tripods would be very helpful.

Comment by WaypointCharlie posted on Wanted - Uni-Loc tripod - Major System 1600 or Major System 2300 at 27/04/2015 - 10:10

WaypointCharlie
Many thanks Vic. Very helpful.

Comment by WaypointCharlie posted on Wanted - Uni-Loc tripod - Major System 1600 or Major System 2300 at 25/04/2015 - 13:51

WaypointCharlie
Thanks again Vic. Do you find the Standard 1700 stable enough? Do you ever feel you'd prefer a Major 1700? Do you many use it for low level photography?

Sorry, so many questions, just when the Standard System1600/1700 come up on eBay I wonder if I should be holding out for a Major System version.

Comment by WaypointCharlie posted on Wanted - Uni-Loc tripod - Major System 1600 or Major System 2300 at 25/04/2015 - 12:55

WaypointCharlie
Hi Vic, thanks for your response.

I find the Uni-Loc range (past and present) a bit confusing. Do you have the Standard System 1700 or the Major System 1700 (I think the outer tube diameter is 30mm on the Standard and 35mm on the Major)? I guess you probably have the Standard System 1700. If so, do you find it stable enough? The Benbo Trekker I tried seemed prone to vibration at some setups, but then the outer tube diameter was only 27.5mm.

I think a Standard System 1700 would be fine for low level work and is something you could tolerate carrying with you for hours. Pity it only goes up to about 1.15m with the column down. Perhaps the solution is getting a Standard System 1700 AND a Major 2300!

These Uni-Loc tripods do come up on eBay (some at the moment). I missed a couple of 2300's recently, thinking they'd be too big, but I realise now that the 1700 would sometimes be too small.

I love the way the tripods work and am surprised how quick and easy I find them, given my normally poor spatial awareness. Mind you, I've only just discovered the way the legs go through 360 degrees, so you don't have to move the head to the other end of the column when you switch between working high and low!

Comment by WaypointCharlie posted on Wanted - Uni-Loc tripod - Major System 1600 or Major System 2300 at 25/04/2015 - 11:48

WaypointCharlie
I'm on the lookout for a Uni-Loc Major System 1600 or the monster Major System 2300. I'm in no particular hurry so am willing to wait until the right one comes up on eBay. However, I thought I'd ask here, just in case someone local has one sitting in their loft.

I might consider the Benbo 1 / Benbo 2 but the Uni-Loc System has a few advantages over the Benbo. I won't consider the Benbo Trekker - I had a look at a friend's Trekker and at full height, even with the column down, the vibration was a lot worse than on my Velbon Ultra REXi L travel tripod.

Comment by WaypointCharlie posted on Wanted - Uni-Loc tripod - Major System 1600 or Major System 2300 at 24/04/2015 - 16:23

Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo