pentaxian450

Joined: 10th February 2008

All Forum Comments

Topics Created Topics Contributed Forum Comments Photo Comments

All Forum Comments

pentaxian450
The Sigma you have works fine on digital. You'd be changing just for the sake of changing. If I was you, I'd put the money for a second flash (preferably the same thing, so the interface is the same), or, if you don't use flash much, toward an extra lens.

Comment by pentaxian450 posted on Which Flash for my K7 ? at 20/04/2011 - 23:44

pentaxian450
Frogherder wrote:
another similar one that also moves side to side.
Those rails are done to help composing the pictures at large magnification ratio. When your subject is very close, trying to move the camera sideway just a "tad" is next to impossible on a tripod, so you use a rail that allows small, accurate moves sideways.

Comment by pentaxian450 posted on Focus stacking at 19/04/2011 - 10:08

pentaxian450
Something not so good for the "old timer": he extended the center column instead of extending the legs of the tripod. Maybe he took so long because he was waiting for the wind to die!

Comment by pentaxian450 posted on The Old way at 19/04/2011 - 01:52

pentaxian450
It can also be done by taking multiple shots without a focus rail, but altering the focus slightly between each pictures. You can also use Helicon focus to combine the pictures: http://www.heliconsoft.com/heliconfocus.html

Comment by pentaxian450 posted on Focus stacking at 18/04/2011 - 21:21

pentaxian450
Since your lens is manual focus, any polarizer will work with it, unless you use the AF hexagon to get focus confirmation. If it says on the packaging that it's a CPL, then I'd assume it is.

Comment by pentaxian450 posted on Help me with a weird problem at 16/04/2011 - 23:01

pentaxian450
MrCynical wrote:
It shouldn't do: if I understand it rightly, having a higher resolution sensor increases the maximum result which can be measured but does not decrease anything. For example if they were to retest the FA43 with the K5, then its measured centre resolution at f4 would be higher (because it exceeded the measuring capabilities of the K10D sensor) but the measured centre resolution at f1.9 would be the same .
Whenever you put a lens on a higher resolution sensor, you always get an improvement over the lower resolution sensor. Depending on the lens, the improvement might not be large, but it will be there. Saying that a sensor over resolve a lens is a misconception invented by people with bad optics knowledge.

Comment by pentaxian450 posted on 18-135 has been slaughtered by Photozone at 16/04/2011 - 22:41

pentaxian450
There are two types of polarizer: circular and linear. Linear polarizer are known to throw AF off with some lens/camera combo. For AF cameras, you should always use a circular polarizer. You should verify to make sure your polarizer is really a circular one. Beside that, I have no idea as to what could cause your problem.

Comment by pentaxian450 posted on Help me with a weird problem at 16/04/2011 - 22:35

pentaxian450
It contains an extra lens to allow correct focusing due to the register distance increase. Every time you add a piece of glass, quality suffers.

Comment by pentaxian450 posted on Nikon to Pentax adaptor? at 16/04/2011 - 20:55

pentaxian450
Cisco wrote:
It can therefore instruct the lens to move directly to the correct position, without taking a second measurement or "hunting" around.
It doesn't exactly works like that. Since some lens have a longer focus throw than others, and since some lens screwdrive don't all use the same "drive ratio", the AF takes an "educated guess" to send the lens close to where the focus point should be for the AVERAGE lens, then it refines the focus in smaller steps.

But, if the camera's AF sensor is not perfectly located, or if the secondary mirror is not at the perfect angle to send the right part of the subject on the AF sensor, you still end up with a front/back focus problem.

Comment by pentaxian450 posted on Why do some lenses have front/back focus issues? at 16/04/2011 - 00:43

pentaxian450
Cisco wrote:
But ALL those components are in the Camera body !! So how can the lens make any difference ?? It will be the same error for ALL lenses ?? No ?
Lenses also suffer from manufacturing variations. The focus sensor might not see the light exactly as the image sensor does. Add to that the color fringing of some lens, diffraction and reflections, color temperature, and you have quite a few things that can confuse the AF sensor.

I personally think the success rate of the AF system on most cameras is very good, given all the variables.

Comment by pentaxian450 posted on Why do some lenses have front/back focus issues? at 15/04/2011 - 15:52

Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo