pentaxian450

Joined: 10th February 2008

All Forum Comments

Topics Created Topics Contributed Forum Comments Photo Comments

All Forum Comments

pentaxian450
Quote:
I've just been looking at http://en.wikipedia.org/wiki/Fluorescent_tube

Modern tubes with electronic ballast are flicker-free, but notwithstanding that, the article reminds us of the way these tubes work.

The charged gas is in plasma state and releases photons in the UV part of the spectrum. These photons hit and excite the phosphors than line the glass tube. The phosphors fluoresce with visible light, just like a CRT monitor. The colour of the light depends upon the phosphors used, not the nature of the AC power.

There is no mention in the article of changing colour balance and I really don't see how there would be.

Hope that helps!
Wikipedia stated that COMPACT fluorescent WITH electronic ballast are "flicker" free. The standard 4ft and 8ft are NOT flicker free.

Comment by pentaxian450 posted on I've a white balance problem - any ideas? at 06/04/2008 - 13:13

pentaxian450
Quote:
I was going to quote one post but there are nuggets of truth in many of them.

here's my take:

Fl lights cycle off and on but it is now very unusual for them all to be doing it together, if the pictures were taken in an old building with old lights then maybe this would be the cause. Flourescent lighting is murder, the spectrum is incomplete, to white balance, as Don says manual WB is the way to go but you are never going to get the range of colours you get in daylight.
They should ALL flicker at the same time, since the current changes at the same time for ALL of them.

Comment by pentaxian450 posted on I've a white balance problem - any ideas? at 05/04/2008 - 23:09

pentaxian450
Quote:
Doing an animated GIF shows us a cycle through the 4 images, notice how the colour does change slightly between the two showing similar tints, a bit more magenta seems to creep in. Also, the more orangy ones are darker - is this when the FL tube is 'off'?

Comment Image


Dan
If you use a K20D in burst mode, you will be able to see a lot more of the flickering effect. This is one of the reason they never use fluorescent as main lighting on a movie stage. It makes editing a nightmare. As to where I got the info, well just remember I'm 50 and my old school physics books are long gone. The best thing you can do with fluorescent is to shoot RAW and correct in post.

Comment by pentaxian450 posted on I've a white balance problem - any ideas? at 05/04/2008 - 20:22

pentaxian450
When the AC current changes direction with tungsten light, the filament doesn't have time to cool down, so the color temp. doesn't change, but fluorescent light are using a ionized gas to produce light. When the current changes direction, that gas isn't ionized anymore (for a very short time) and henceforth changes the color temperature for a very brief time. This is the reason why it is nearly impossible to get accurate white balance with fluorescent lighting. And to top it off, different manufacturers of fluorescent tubes will use different mix of gas to end up with what is their idea of daylight, so that makes it impossible for camera manufacturers to get a good fluo. adjustment on their cameras.

Comment by pentaxian450 posted on I've a white balance problem - any ideas? at 05/04/2008 - 13:56

pentaxian450
That is likely caused by AC current. The - and+ on AC change direction 60 times a sec. (in North America, I think 50 in your world), so when you take a picture and you happen to push the button as the AC change direction, it "confuses" the white balance. With the K20D in burst mode, tou can easily see that situation in a sequence.

Comment by pentaxian450 posted on I've a white balance problem - any ideas? at 02/04/2008 - 17:37

pentaxian450
Quote:
Well the sun has been shining here, for . . . weeks actually. 21 degrees C indoors, it's getting warm . . . I can't remember the last time we had rain, and snow is (almost) unheard of this far south.

Summer's not coming for us . . . it's here.

Summer does have it's downside though, 45 degrees inside in the summer is unbareable.
That is downright dirty. Do you really have to rub it in?

Comment by pentaxian450 posted on Summertime at 31/03/2008 - 00:48

pentaxian450
Quote:
Gwyn wrote:
For those of you in Europe - don't forget to reset the clock in your camera for summertime
Along with the microwave, alarm clock, mobile phone, car etc etc. I always manage to forget to change something until a few weeks have gone by (usually the camera . )
We have another week to go before returning to non daylight saving
it always depresses me when it gets dark at 5.30pm so i am not looking forward to going back.
You shouldn't complain. In your part of the world, days get shorter, but you don't get burried under 2 metres of snow. Right now, this is what I have to deal with in my backyard. I like winter sports, but it comes to a point wher too much is really too much!

Comment by pentaxian450 posted on Summertime at 30/03/2008 - 12:13

pentaxian450
Quote:
If you keep the button pressed on either remote it will take all the shots, but again not if you only press once.
Weird that they changed it in the firmware update though.
I don't know either why they changed it, but on the K20D, you can set it either way. Go figure....

Comment by pentaxian450 posted on Help! Auto Exposure Bracketing not working with new K10D. at 31/03/2008 - 00:54

pentaxian450
Pressing the button once worked with the original firmware, but if you upgraded to firmwdare 1.30, you need to keep the shutter button down for all the sequence to go thru, or release manually for every single shot of the sequence.

Comment by pentaxian450 posted on Help! Auto Exposure Bracketing not working with new K10D. at 30/03/2008 - 12:23

pentaxian450
Does the "no postage charge" apply for those of us living outside the U.K.?

Comment by pentaxian450 posted on Straps! at 27/03/2008 - 17:08

Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo