All Forum Comments
Comment by jeallen01 posted on Advice wanted re a graduated ND grad - screw fit, not gel or similar! at 14/08/2017 - 22:55
Comment by jeallen01 posted on Hello from West Sussex at 13/08/2017 - 20:59
You made it
Comment by jeallen01 posted on Hello from West Sussex at 13/08/2017 - 20:26
Comment by jeallen01 posted on Hello from West Sussex at 13/08/2017 - 18:05
I have to say your post has done nothing for my arachnophobia !!
(Nothing less than a very "angry" tarantula or similar spider would phase me - OTOH, SWMBO is freaked by anything more than an inch across and so I have to "get rid of it", which, where possible, I do by trying to collect and deposit it outside the house where it can do more "good" )
Comment by jeallen01 posted on Spiders at 12/08/2017 - 21:18
The Flipside arrived this morning (at 7.15 - that's unfortunately when the parcels get delivered!) but I didn't get a chance until later to open the parcel and move the stuff from my 350AW.
Everything seems to fit fairly nicely although I had to ditch quite a few of the dividers (LowePro always seem to provide rather too many).
By comparison with the 350AW, there is certainly a little more volume in the form of the depth, which makes the Flipside easier to close when full (and it already is with 2 gripped bodies and 2 long Sigma zooms) . OTOH many of the accessory pockets are not so easy to access because the lip/flap doesn't stay up too easily - not your fault, it's a design issue! - maybe that will get better with use.
Generally pretty happy overall.
Many thanks
John
Comment by jeallen01 posted on F.S. a few bags, and other bits and bobs. at 10/08/2017 - 16:55
Re those Tuoro drives - the review looks good.
However, I would have a reservation about using all exactly the same drives - it's that (seriously!) well-known reliability engineering concern of "Common Mode Failure", which means, you never use 2 identical components/assemblies in parallel to provide a "fail safe" solution because if one does fail then there is a relatively high probability that the second one will fail in the same manner (especially if they came from the same production batch)!
Comment by jeallen01 posted on Offlining photos with Photoshop Elements at 08/08/2017 - 13:49
- External ones without PSUs generally have 5400rpm and not 7200rpm mechanisms, and so are likely to be slower to save to/retrieve from.
- Always get USB3 versions even if the current computer only has USB2 ports because that will probably be upgraded at some point to one that does have USB3 ports - and data transfer via those is MUCH faster
- Don't just buy "any old" USB 3 drive - try to get one that is designed for long-term storage and make sure it comes from a manufacturer that gives a long (3yr min) warrantee because you want to be sure it will last as long as possible (for me that means the WD "Red" range, or similar ones from Samsung, Seagate and so on).
- If you can't find a suitable complete external USB3 enclosure and decent disk, just buy the disk of your choice and fit it into an enclosure from another source because it's pretty much a case of just undoing a few screws to open the enclosure, slotting in the disk, and then screwing the cover back on again. Takes 10 mins max!
Comment by jeallen01 posted on Offlining photos with Photoshop Elements at 08/08/2017 - 12:55
The C/U has arrived as promised and looks very good - impressive packaging too!
Comment by jeallen01 posted on WTB - Decent quality 72mm Close-up lens? at 08/08/2017 - 12:38
PM & payment sent for the Flipside
Comment by jeallen01 posted on F.S. a few bags, and other bits and bobs. at 08/08/2017 - 09:19


Not interested in gel/similar or plastic (like some Tiffen) ones as they would not last a couple of days with the way I store/use them!
So, your suggestions would be appreciated - Thanks in advance.