All Forum Comments
Comment by Frogherder posted on Scam Site? at 26/04/2011 - 11:17
I've now stripped and rebuilt the lens and am moderately happy with the results. The blades are not as "snappy" as I expected but moving freely at least. I suspect the return spring is a bit soft- not surpising after 40 odd years I suppose.
Despite Hefty's warnings about removing the blades this was imposed upon me when they all fell out so I simply picked them up with tweezers, put them into a small dish of surcical spirits whils I attended to the rest of the lens assy. After picking them out and leaving to dry on kitchen paper I found re-assembly fiddly but not too onerous, just as well because they fell out several times further. [Method-Set the aperture to 2.8 and proceed clockwise, gently easing the last one into place].
I was unable to disassemble the front and middle lens or the aperture setting ring, but they looked clean anyway (curiously there is a small red fibre between the lenses but it stayed at the edge no matter what I did.)
Because of the multistart thread I had to try several times to realign the scales (each time manging to dislodge the iris blades) but eventually everything went back together with a deligtful bonus - no bits left over.
Not wanting to wait for prints to come back I set the lens into a 7mm extention tube, using a 40mmx30mm brass washer to depress the auto pin and mounted the lens via a M42/K adapter on my K10D and took the following shots, the first at f2.8 and the 2nd at f8. :-
[IMG]http://i1236.photobucket.com/albums/ff444/Frogherder/IMGP5517a.jpg[/IMG]
[IMG]http://i1236.photobucket.com/albums/ff444/Frogherder/IMGP5518a.jpg[/IMG]
On my 15x12 screen they don't look the best in the world but I suppose good enough for 6x4 prints
Bernard
Comment by Frogherder posted on Iris Cleaning - The final chapter (I hope) at 26/04/2011 - 10:39
I can now see the back of the blades - not touched them in view of previous comments.
I suspect the next stage is to separate the depth of field ring from the back secrion but I can't for the life of me see how. Is it sweated on or is it screwed-I can't shift it either way and I'm sure force isn't the way
:::
Bernard
Comment by Frogherder posted on Iris cleaning at 22/04/2011 - 17:51
On a serious note - I don't know but try :-
http://www.aircav.com/recog/chp10/ch10.html
Bernard
Comment by Frogherder posted on What are they? at 22/04/2011 - 12:16
I've been asked to clean an old lens for someone.
It's a Domiplan 2.8/50 automatic lens. (M42)
The glass is perfectly clear but the aperture iris sticks, and after a few "jiggles" i can get it to move - as if through treacle.
Inspection of the blades (though either front or back lens) shows what appears to be an oily film. Is this likely to be the cause. If so where's it suddenly come from?
If so what is the best course of action.
I can see how the lens comes apart and have the necessary tools (I spent many years in instrument engineering) but concerned that specialist devises night be needed to get the optics back in line if I remove these to get at the iris.
If it were my lens I'd probably bite the bullet as without cleaning it's as good as scrap anyway, but it's not and my elderly friend is not likely to change to digital and he's had the same old camera for as long as I've known him, certainly since the early 70's I think. I've never seen anything bigger than 6x4 when he's shown me what he's taken.
So any suggestions would be appreciated:-
1 Is it safe to dissemble
2 What is the best cleaning material (If I get that far) (I would normally use surgical spirits).
3 Is it likely to require re-alignment.
I think I've included everything that might be relevant
regards
Bernard
Comment by Frogherder posted on Iris cleaning at 22/04/2011 - 12:02
Ah but sometimes they bring Grandchildren which makes it all worthwhile
May I also take this oppurtunity to wish every one a Very Happy Easter, whatever you race, colour or creed.
regards
Bernard
Comment by Frogherder posted on Another pointless thread at 22/04/2011 - 11:41
Bernard
Comment by Frogherder posted on Another pointless thread at 21/04/2011 - 20:28
I think being named after a high end lens would be OK. Preferable to a kid in my daughter's class who is called Acer; it always struck me as a bit unfortunate to have a name that most people will associate with either a laptop or a tree.
Did you know the Japanese have special tools for planting these trees.
Acer Spades
Bernard
Comment by Frogherder posted on Another pointless thread at 21/04/2011 - 15:28
Spent lunch in the garden still experimenting. I thought I'd add my extention tubes and from several feet away got the following :-



I got a lot of blurred ones as well (there is just enough breeze) but you probably don't want to see those.
These were all taken with the AS set to 500, but AS off and tripod mounted. None are cropped, only resized tp 800px
regards
Bernard
Comment by Frogherder posted on Trying out an old lens at 21/04/2011 - 15:13
More unusual designs for the Pentax K-r
Blend into your surroundings with a camouflaged Pentax K-r.
I would think a bit of decorum lends a degree of seriousness to what is said to be a fine camera
Bernard
Comment by Frogherder posted on Wow? No at 21/04/2011 - 14:19


Bernard