ChrisPlatt

Joined: 1st July 2011

All Forum Comments

Topics Created Topics Contributed Forum Comments Photo Comments

All Forum Comments

ChrisPlatt
Oso wrote:
Just don't forget to put on the lens cover.
The SP-F meter switches off when you place the lens cover on.
The venerable K1000 works the same way...

Chris

Comment by ChrisPlatt posted on Sensible M42 metered body to use today? at 10/06/2012 - 19:10

ChrisPlatt
FWIW the Pentax Spotmatic F (SP-F) meters at full aperture,
but only using Super-Multi-Coated (or SMC) Takumar lenses.
Stop-down metering must be performed when using other lenses.

Chris

Comment by ChrisPlatt posted on Sensible M42 metered body to use today? at 06/06/2012 - 02:25

ChrisPlatt
I too like the simplicity of the SP1000. It's my only screwmount body.
I never use self-timer, and it's easy to find the right size battery.
Another benefit is that some are ten years newer than the original SP.

Chris

Comment by ChrisPlatt posted on Sensible M42 metered body to use today? at 06/06/2012 - 02:20

ChrisPlatt
I was checking some older saved links and stumbled across this,
from the well-respected AOHC website: http://www.aohc.it/batte.htm

Please note the highlighted text...

Chris

Comment by ChrisPlatt posted on Sensible M42 metered body to use today? at 04/06/2012 - 17:33

ChrisPlatt
The KX was my first Pentax body and remains my favorite.
It is an excellent manual focus, manual exposure camera with
full-information viewfinder, and it's not too small like the MX.

Chris

Comment by ChrisPlatt posted on Pentax KX at 20/05/2012 - 13:23

ChrisPlatt
ChrisR wrote:
You carry on using whatever battery you like, that makes you happy but please try to refrain from misleading others.

Please don’t start getting personal this forum is not for that,.
For the record, I am a British trained, industrial electrical engineer, you can not get better than that.
It seems you are the one misleading others as empirical evidence has shown the following to be true:

A modern 1.5V cell will provide accurate exposure readings in any Spotmatic series camera.
The readily available silver oxide variety will provide stable output and long service life.


Armchair theorizing aside, I suggest you swallow your pride and actually try one in your SPII.

If it matters I am an experienced professional electronic technician, working in the field for more than 25 years.
After completing technical school my first employment was in the field of camera repair for a major manufacturer.

Chris

Comment by ChrisPlatt posted on Sensible M42 metered body to use today? at 20/04/2012 - 02:19

ChrisPlatt
ChrisR wrote:
Below a brief description of various battery/cell types.

The Pentax Spotmatic II, along with other cameras of that era with similar light/exposure metering, did not have complicated circuits, number one electronics in miniature was not available, number two, they were not necessary.
This is why the mercury cell was ideal for any application which was voltage dependent for its accuracy, the open voltage for the single mercury cell was 1.35 v, but it was the discharge characteristics which was most important. The mercury cell throughout its service/discharge life, had an almost flat voltage decay curve, meaning that the voltage was almost constant at 1.35 volts, until the end of its life, when there was a sudden fall off voltage, and fail. This service life under light usage could be as much as, two to three years or more.

So cameras, such as the spotmatic II, would have the light/exposure meters calibrated to give a correct reading at 1.35 volts, as indicated above and would be accurate/stay in calibration throughout the mercury cell’s life.

The alkaline cell when new has an open circuit voltage of, 1.5 to 1.65 v, the discharge characteristics of these cells has a steady voltage decay curve to end of live (total discharge). This higher start voltage will not damage the spotmatic II light/exposure meter circuit but it will give a high light/exposure indication, meaning that you will have an under exposure of film used, this high light reading will steadily reduce as the cell voltage drops through use, at the brief point when the discharge of the cell passes through 1.35 volts, the light/exposure reading will be correct/accurate, however as the cell voltage steadily drops through further discharge the light/exposure will get increasingly low, causing an over exposure of film used.

The zinc air cells have a start voltage of around 1.32v, therefore very close to the original mercury cell voltage, giving a correct light/exposure reading. The discharge characteristics of these cells are virtually the same as the mercury, an almost flat voltage decay curve. The main disadvantage of these cells, is the service life, before use, you remove the seal over a small hole in the cell, which allows air to enter the cell and activate it, the cells, life is then dependant on time, (ie) if the cell was not used after the seal was removed, total discharge will still occur in approx thirty to sixty days.

I hope the above clears up any misunderstanding of the different cells, and makes clear that the cell most suitable for purpose is the zinc air. Accepting the short service life, of these cells.


Take care.
Instead of just theorizing about the innacuracy the .2V difference will make, have you actually tried one in your SPII?

Conquer your fear of Google and you will find that there's a 1.5V silver battery to fit any Spotmatic model.
Any good electrical engineer knows that silver cells have a much more stable output than alkalines
and a service life several times greater than than those miserably short-lived zinc-air batteries.

Chris

Comment by ChrisPlatt posted on Sensible M42 metered body to use today? at 18/04/2012 - 21:38

ChrisPlatt
Hardgravity wrote:
I used a modern 'cheap' modern battery in my SPII and this is the result.
Indeed, and my SP1000 works as well with a modern battery too.

Perhaps our cameras are not aware of the results of simple battery voltage compatibility tests?

Chris

Comment by ChrisPlatt posted on Sensible M42 metered body to use today? at 17/04/2012 - 23:39

ChrisPlatt
ChrisR wrote:
I cannot comment on all the Spotmatic, models, but the meter in the Spotmatic II is certainly voltage dependant.
Like the rest of the Spotmatic line your SP II exposure meter incorporates a bridge circuit,
making it relatively immune to variations in supply voltage.
The same is true of the OP's SP1000.

There are numerous discussions of this topic on the Internet.
A majority of users report that a modern 1.5V battery provides readings
as accurate as the original 1.3V mercury cell.

In this Pentax Spotmatic series owners are far luckier than users of many older cameras.

Chris

Comment by ChrisPlatt posted on Sensible M42 metered body to use today? at 16/04/2012 - 23:23

ChrisPlatt
Of all the Spotmatic series cameras I like the simple SP1000 best.
It lacks self-timer and hot shoe, features I never use.

All SP series camera exposure meters can work accurately
with a modern battery as they are not voltage dependent.

There is no need to purchase any special adapter.
The SP1000 works fine with a commonly available battery.
I recommend use of a silver-oxide cell as it will last
far longer than the zinc-air type.

Chris

Comment by ChrisPlatt posted on Sensible M42 metered body to use today? at 15/04/2012 - 16:33

Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo