Lens calibration - Focus Tune software

johnriley
Posted 28/04/2013 - 23:22 Link
There is absolutely no way we can make any conclusion from a hand held test.

I would wait before adjusting anything and start agin with a sturdy tripod and a carefully aligned subject.
Best regards, John
JAK
Posted 28/04/2013 - 23:33 Link
John, some of my macro shots were missing the point of focus, like the stamens in a bloom and similar. By experimenting with the settings I worked out which setting put the matter right (by using that newspaper and the wordsearch.) Re-taking them after the adjustment they were much better, indeed spot on. I hear what you are saying but it isn't rocket science; it really isn't difficult to see whether the focus point is right or not. I cannot see how would your method would come up with a different result, it is either OK or it isn't.

John K
John K
Edited by JAK: 28/04/2013 - 23:33
JAK
Posted 28/04/2013 - 23:58 Link
Just to go back to that software solution. If it doesn't have a dedicated Pentax output, it would still need a trial and error method to determine what actual adjustment is needed unless I'm missing something.

Mostly many put up without making any adjustments to their lenses, if indeed it is provided for in the camera settings. So if an error is suspected it only needs one to determine if it is front or back and experiment. Say put it half way to + or - 5 and see what effect that has had. If it has gone too far, bring it back a bit. If not enough go a bit further. It's the real world results that matter, not those obtained from calibration charts/software designed for other camera systems. If another time it seems wrong it can easily be reset and start again, it could be something changes with the camera so the adjustment needed might change in other conditions. Remember, with the K-5, the change can be made to just the suspect lens (though a universal adjustment is available.)

John K
John K
Edited by JAK: 29/04/2013 - 00:09
johnha
Posted 29/04/2013 - 00:09 Link
I don't understand the issue. The only variable can be the camera body (lens mount, AF sensor & focus screen alignments). The AF system from the SFX onwards (maybe the MEF for all I know) is supposed to continually feedback to get the least phase difference between the two 'halves' of the sensor (i.e. the most 'in focus'). The only other explanations are that the AF system doesn't feedback to increase AF speed at the expense of accuracy or that the resolution of the AF stepper motor/mechanism isn't precise enough!

Any variation in the lens should be taken care of with the feedback in the above. The only difference could be whether the lens is focusing from in front or behind the subject (i.e. which edge of the DoF it hits first).

It may be that the body needs adjusting differently for different focal lengths, but this shouldn't be necessary for different copies of the same lens (unless there's something very inconsistent with lens manufacture).

The cameras and lenses are built in a very precise manufacturing environment, any variations are going to be far less than any variables introduced by a 'user' test except using the most controlled laboratory tests.

It's like paying a fortune for a new car then taking it round to your mates garage to have the suspension lowered because he knows a lot more than the manufacturers who spent millions designing and testing it in the first place!
johnriley
Posted 29/04/2013 - 00:25 Link
JAK, what would you think if Pentax adjusted their cameras and lenses by using a hand held test? I'm afraid you have to be precise if you are making measurements. Your adjustment is nowhere near precise.

I only mention it because you are making changes based on some very error prone methodology.
Best regards, John
Smeggypants
Posted 29/04/2013 - 00:35 Link
johnriley wrote:
There is absolutely no way we can make any conclusion from a hand held test.

I would wait before adjusting anything and start agin with a sturdy tripod and a carefully aligned subject.
If course you can.

I do all my AF adjustments hand held. Why? Because it works.


All this is being blown out of all proportion, not least of which by this pointless software.

It's quite simple:

Take a few pics at widest aperture of something, usually at an angle so front of back focussing can be easily discerned, like the text shown in the example posted in this thread.

If you get consistent back or front focussing, dial in a plus or minus adjustment and take some more pics. if you overshoot the adjustment dial it a bit back again. When you've achieved the correct adjustment take some more pics at different focussing distances adn a few objects and verify it's still correct. if so job done. Simples

There's no need whatsoever for tripods, focussing charts, accurate alignments and especially software.

Anyone would think AF tweaking is akin to bomb defusing the way this thread is going
[i]Bodies: 1x K-5IIs, 2x K-5, Sony TX-5, Nokia 808
Lenses: Pentax DA 10-17mm ED(IF) Fish Eye, Pentax DA 14mm f/2.8, Sigma 17-70mm f/2.8, Pentax-A 28mm f/2.8, Sigma 30mm F1.4 EX DC, Pentax-A 50mm f/1.2, Pentax-A 50mm f/1.4, Pentax-FA 50mm f/1.4, Pentax-A 50mm f/1.7, Pentax DA* 50-135mm f/2.8, Sigma 135-400mm APO DG, and more ..
Flash: AF-540FGZ, Vivitar 283
Smeggypants
Posted 29/04/2013 - 00:40 Link
johnha wrote:


The cameras and lenses are built in a very precise manufacturing environment, any variations are going to be far less than any variables introduced by a 'user' test except using the most controlled laboratory tests.

In the real world it doesn't work like that for AF adjusting. Teh fact is that Lenses ( both own brand and 3rd party - or should that be 2nd party? ) can back or front focuss.

I have two K-5s. I have some lenses that require no adjustment on either K-5, some lenses that require the same adjustment on both K-5s, some lenses that only require adjustment on one K-5 and some lenses that require a different adjustment on each K-5

I have no idea why this is the case but it is.

Adjusting the AF parameter for each lens on each camera fixes the problem
[i]Bodies: 1x K-5IIs, 2x K-5, Sony TX-5, Nokia 808
Lenses: Pentax DA 10-17mm ED(IF) Fish Eye, Pentax DA 14mm f/2.8, Sigma 17-70mm f/2.8, Pentax-A 28mm f/2.8, Sigma 30mm F1.4 EX DC, Pentax-A 50mm f/1.2, Pentax-A 50mm f/1.4, Pentax-FA 50mm f/1.4, Pentax-A 50mm f/1.7, Pentax DA* 50-135mm f/2.8, Sigma 135-400mm APO DG, and more ..
Flash: AF-540FGZ, Vivitar 283
Edited by Smeggypants: 29/04/2013 - 00:43
johnriley
Posted 29/04/2013 - 00:42 Link
If that's the case, I'm not surprised that you adjust all your lenses.
Best regards, John
Smeggypants
Posted 29/04/2013 - 00:43 Link
johnriley wrote:
JAK, what would you think if Pentax adjusted their cameras and lenses by using a hand held test? I'm afraid you have to be precise if you are making measurements. Your adjustment is nowhere near precise.

I only mention it because you are making changes based on some very error prone methodology.
It's not error prone. It works. You set the adjustment and go out and take photos that are in focus.
[i]Bodies: 1x K-5IIs, 2x K-5, Sony TX-5, Nokia 808
Lenses: Pentax DA 10-17mm ED(IF) Fish Eye, Pentax DA 14mm f/2.8, Sigma 17-70mm f/2.8, Pentax-A 28mm f/2.8, Sigma 30mm F1.4 EX DC, Pentax-A 50mm f/1.2, Pentax-A 50mm f/1.4, Pentax-FA 50mm f/1.4, Pentax-A 50mm f/1.7, Pentax DA* 50-135mm f/2.8, Sigma 135-400mm APO DG, and more ..
Flash: AF-540FGZ, Vivitar 283
Smeggypants
Posted 29/04/2013 - 00:46 Link
johnriley wrote:
If that's the case, I'm not surprised that you adjust all your lenses.
How do you mean 'not suprised' ?

Anyway I don't adjust all my lenses. As said above some haven't needed adjustment. I do however check the AF on a every lens when I first purchase them. I did recheck them a few months ago as it was over a year since I tested and tweaked those that required it and I was pleased to say they needed no further adjustment, so nothing on the camera or lenses had drifted
[i]Bodies: 1x K-5IIs, 2x K-5, Sony TX-5, Nokia 808
Lenses: Pentax DA 10-17mm ED(IF) Fish Eye, Pentax DA 14mm f/2.8, Sigma 17-70mm f/2.8, Pentax-A 28mm f/2.8, Sigma 30mm F1.4 EX DC, Pentax-A 50mm f/1.2, Pentax-A 50mm f/1.4, Pentax-FA 50mm f/1.4, Pentax-A 50mm f/1.7, Pentax DA* 50-135mm f/2.8, Sigma 135-400mm APO DG, and more ..
Flash: AF-540FGZ, Vivitar 283
JAK
Posted 29/04/2013 - 01:12 Link
johnriley wrote:
JAK, what would you think if Pentax adjusted their cameras and lenses by using a hand held test? I'm afraid you have to be precise if you are making measurements. Your adjustment is nowhere near precise.

I only mention it because you are making changes based on some very error prone methodology.
Sorry John, I'll have to beg to differ. We take a photo of something and the AF is missing the correct focus point. We just make a simple quick adjust so that it does it correctly! It can be reset right afterwards as quickly as changing any other menu setting. To solve the issue in the field we would have to use a rough and ready solution as we do not carry round test equipment, charts, rulers or even tripods to set up to do it precisely. If a hand held solution works, why make it more complicated.

If someone wishes to adjust it scientifically then I have no issue with that, but that might not help in another lighting condition, remember the front/back focus issue when used in say, tungsten lighting which was a reported problem some had with the early firmware on the K-5.

What isn't stated is what the increments represent and there appears to be no formal guidance on the subject.

I wish to point out that I've only ever found the need to adjust that one particular lens. Others may benefit I suppose but I haven't had an issue with them.

John K
John K
Edited by JAK: 29/04/2013 - 01:27
JAK
Posted 29/04/2013 - 01:19 Link
When it comes to the K-5 Horizon correction feature, it might have helped if Pentax had tried some hand held test shots to make sure that works properly, and provide an adjustment for when it doesn't. I believe most users just turn that feature off.

John K
John K
Edited by JAK: 29/04/2013 - 01:21
Smeggypants
Posted 29/04/2013 - 01:26 Link
JAK wrote:
When it comes to the K-5 Horizon correction feature, it might have helped if Pentax had tried some hand held test shots to make sure that works properly, and provide an adjustment for when it doesn't. I believe most users just turn that feature off.

John K
I never use it. I correct anything in lightroom that needs correcting. hold CTRL and draw a line over your horizon and job done.
[i]Bodies: 1x K-5IIs, 2x K-5, Sony TX-5, Nokia 808
Lenses: Pentax DA 10-17mm ED(IF) Fish Eye, Pentax DA 14mm f/2.8, Sigma 17-70mm f/2.8, Pentax-A 28mm f/2.8, Sigma 30mm F1.4 EX DC, Pentax-A 50mm f/1.2, Pentax-A 50mm f/1.4, Pentax-FA 50mm f/1.4, Pentax-A 50mm f/1.7, Pentax DA* 50-135mm f/2.8, Sigma 135-400mm APO DG, and more ..
Flash: AF-540FGZ, Vivitar 283
JAK
Posted 29/04/2013 - 01:28 Link
I doubt anyone uses it, it doesn't work (which is actually a shame!)
John K
Edited by JAK: 29/04/2013 - 01:29
Smeggypants
Posted 29/04/2013 - 01:31 Link
JAK wrote:
johnriley wrote:
JAK, what would you think if Pentax adjusted their cameras and lenses by using a hand held test? I'm afraid you have to be precise if you are making measurements. Your adjustment is nowhere near precise.

I only mention it because you are making changes based on some very error prone methodology.
Sorry John, I'll have to beg to differ. We take a photo of something and the AF is missing the correct focus point. We just make a simple quick adjust so that it does it correctly! It can be reset right afterwards as quickly as changing any other menu setting. To solve the issue in the field we would have to use a rough and ready solution as we do not carry round test equipment, charts, rulers or even tripods to set up to do it precisely.
You can't do it any more precisely than the increments provided for anyway. ( Although I think the settings in debug mode might allow for smaller increments, although that is an overall adjustment )



Quote:

If someone wishes to adjust it scientifically then I have no issue with that, but that might not help in another lighting condition, remember the front/back focus issue when used in say, tungsten lighting which was a reported problem some had with the early firmware on the K-5.

What isn't stated is what the increments represent and there appears to be no formal guidance on the subject.
I don't think teh increments can represent anything other than teh amount of micrometers the AF sensor moves by. Each lesne, focal distance, etc, will be different to how much this applies to a certain distance out of focus anyway


Quote:

I wish to point out that I've only ever found the need to adjust that one particular lens. Others may benefit I suppose but I haven't had an issue with them.

John K
Given it only takes a minute or two to check them, why no do so?
[i]Bodies: 1x K-5IIs, 2x K-5, Sony TX-5, Nokia 808
Lenses: Pentax DA 10-17mm ED(IF) Fish Eye, Pentax DA 14mm f/2.8, Sigma 17-70mm f/2.8, Pentax-A 28mm f/2.8, Sigma 30mm F1.4 EX DC, Pentax-A 50mm f/1.2, Pentax-A 50mm f/1.4, Pentax-FA 50mm f/1.4, Pentax-A 50mm f/1.7, Pentax DA* 50-135mm f/2.8, Sigma 135-400mm APO DG, and more ..
Flash: AF-540FGZ, Vivitar 283

Add Comment

To leave a comment - Log in to Pentax User or create a new account.



Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo