golfdiesel

Joined: 12th January 2006

All Forum Comments

Topics Created Topics Contributed Forum Comments Photo Comments

All Forum Comments

golfdiesel
You never know how easy the process of flashing a device is. I have seen enough devices which had to be in a special flashing mode. This flashing mode usually consisted of needing three hands to push a load of buttons while turning the device on and pressing the mousebutton at the same time

Comment by golfdiesel posted on Metz update 30-12-2009 at 11/01/2010 - 05:40

golfdiesel
debug mode hasn't any real uses for the K20D to my knowledge.

Comment by golfdiesel posted on ANNOYING DEBUG MODE at 10/01/2010 - 15:09

golfdiesel
Don't expect very good results from those cheap scanners.
If I were ever to go and digitize my slides it will be with a high quality scanner.
I had a cheap one and it was very slow and it took a lot of time in post processing as well.

Comment by golfdiesel posted on Convert film to sd card at 10/01/2010 - 10:36

golfdiesel
ah well, there is allways Wine:

http://wiki.winehq.org/MacOSX

Comment by golfdiesel posted on Metz update 30-12-2009 at 10/01/2010 - 10:32

golfdiesel
Ok, Pentax, something to add to future bodies

http://www.gizmag.com/hasselblad-h4d-true-focus-60-megapixel/13503/

Quote:
"Due to the physics of an SLR-camera, the off-center focus points that are offered are all clustered relatively close to the center of the image. To set focus outside of this center area, the photographer is still forced to focus first, and then shift the camera to reframe, with the resulting loss of focus as a result." Hasselblad has overcome this problem by using modern yaw rate sensor technology to measure angular velocity in an innovate way. The result is the new Absolute Position Lock (APL) processor, which forms the foundation of Hasselblad's True Focus feature.

The APL processor logs camera movement during any re-composing, then uses these exact measurements to calculate the necessary focus adjustment, and issues the proper commands to the lens's focus motor so it can compensate. The APL processor computes the advanced positional algorithms and undertakes the required focus corrections at such a rapid speed that Hasselblad says no shutter lag occurs. The H4D's firmware then further perfects the focus using the precise data retrieval system found on all HC/HCD lenses.

“This technology takes AF to an entirely new level, correcting for the vertical and horizontal focus-shift that results from the rotation of the camera around an axis close to camera, said Poulsen. “In simple terms, True Focus allows the photographer to concentrate on their composition, to focus on their creativity, while True Focus takes care of the other, more mechanical focus.”

Comment by golfdiesel posted on Hasselblad "true focus feature" at 07/01/2010 - 20:06

golfdiesel
The DNG format is an open format as far as I know so for software like silkypix it shouldn't make a difference.

If the filesize is about the same I would opt for DNG as well.

Comment by golfdiesel posted on K7 arrived at 07/01/2010 - 05:20

golfdiesel
Well, measuring does the trick.

In the past people who asked Pentax about it got the answer that the ist-D and ist-DS could take up to 30 volts or so, but those bodies could handle plain TTL so perhaps the circuitry was allso able to handle higher voltages then the later models.

I would use a voltmeter to check if the voltage isn't more then around 12 volts as Stefan described.

Placing your finger on the contacts wouldn't really help because you need to make a connection between the center contact and the spring contacts on the side of the socket (center is the positive terminal, spring contacts are the negative terminals).

Comment by golfdiesel posted on Flash compatibility with K-x ???? at 07/01/2010 - 05:17

golfdiesel
The problem is that when you keep using the harddrive on which the pictures were stored then the chance of retrieving them gets quite slim.

Comment by golfdiesel posted on finding deleated pictures on your HDD at 07/01/2010 - 05:13

golfdiesel
Auto mode works differently, it does not meter the surrounding light. It measures the reflected light from the flash and it effectively stops the output of the flash.
example: when I fire the flash in auto mode outside in the open field in complete darkness it discharges completely.
When I fire the flash in our living room in complete darkness it uses much less flashpower allthough the amount of ambient light available is the same or even lower then outside in the open field.

Comment by golfdiesel posted on flash and manual [m] lens on a K10 at 06/01/2010 - 18:48

golfdiesel
With firmware 1.0 it worked like this:
If the Metz was set as wireless master it used the secondary reflector for communication with the wireless slave flashes.
With firmware 1.1 it uses the main reflector for communication purposes.

I will test this to see if it is really the case

Comment by golfdiesel posted on Metz update 30-12-2009 at 05/01/2010 - 19:11

Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo