Frogherder

Joined: 19th February 2009

All Forum Comments

Topics Created Topics Contributed Forum Comments Photo Comments

All Forum Comments

Frogherder
Thanks guys, I'll stay away from this set also.

I have a plane set of tubes on which I use a Pentax-M 1.7 50mm lens perfectly well but as this is the only K mount -M lens I have. I thought an update could be in order, and the price wasn't too bad either.

Ah well, sooner or later an ebay seller will come up with a reasonble price and at the same time I'll be the only one to notice.

regards
Bernard

Comment by Frogherder posted on Extention Tubes at 04/02/2012 - 16:45

Frogherder
Does anyone know how I upload a photograph of an actor up to Google (or, for that matter, someplace else) in oder to find out his name.

regards
Bernard

Comment by Frogherder posted on Another pointless thread at 04/02/2012 - 16:01

Frogherder
Gwyn wrote:
My washing machine is frozen .
It lives in the garage, which is attached to the house, but unheated.
It has survived all previous winters just fine, including colder ones than this, but now it is frozen. I have run it most nights just to keep things moving, but forgot last night.
If you have a hand lamp/small table lamp or inspection lamp. Put a 40W bulb or 15W/25W pygmy bulb in and put it under the machine then cover all with a sheet of polythene. This can be left on overnight at minimum cost and generates just enough heat to keep most things frost free


regards
Bernard

Comment by Frogherder posted on Another pointless thread at 04/02/2012 - 15:58

Frogherder
I'm pretty sure the terminal voltage on this gun is some 200V so enough to likely cause damage to you camera.

Can you hear it whistle when it is switched on? It would be very high pitched, but that would prove that the circuit is generally working.

There is also, usually, a neon lamp which lights when the flash is fully charged (as the batteries run down this would lengthen the time taken until too long to be of any use).

To check the voltage (assuming you have, or have acess to a multimeter) measure the voltage across the central pin and a side contact. The central pin aligns with the middle contact on your hot shoe, the side contact with the long strips at the edge of the hot shoe.

You don't give a location, but if anywhere near Burton I'd be happy to check it over for you


regards
Bernard

Comment by Frogherder posted on Hanimex TS 855 at 04/02/2012 - 15:29

Frogherder
Hi All,

I've found a set of extention tubes which have the following as part of the description :-

"Auto Extension Macro tubes .
Pentax K bayonet mount ( K , PK , PK/M )

Full mechanical iris control of the lens is maintained with the SLR when these tubes are placed between lens and body "


From the included photograph there is no evidence of contacts around the flanges so :-

1. What would be their limitations when used with a K10D and say an 18-55mm kit lens
2. I can accept that I may well need to manually focus the lens.

There are probably a plethora of questions I should ask so any insights would be welcomed

regards
Bernard

Comment by Frogherder posted on Extention Tubes at 04/02/2012 - 01:09

Frogherder
So are they saying it is more about style than substance?

Bernard

Comment by Frogherder posted on Pentax K-01 at 03/02/2012 - 23:59

Frogherder
But do yo dry yourself properly?

Bernard

Comment by Frogherder posted on Lens cleaning (internal) at 03/02/2012 - 17:31

Frogherder
Quote:
and also their PE lessons consisted of skating on the local ponds
Try that in the UK and the PC brigade; the H&S evangelists would make your life hell.


Bernard

Comment by Frogherder posted on Another pointless thread at 03/02/2012 - 14:11

Frogherder
Exactly.

I carve wood (including house signs)

I always suggest a charge, which usually goes along the lines :-

Preparing the wood and research (graphic design of the font) takes about an hour or so.
Each letter takes about 20minutes to cut
Finishing (sanding, oiling/varnish) takes another hour or so.
Cost of materials depends on the timber and finish required.
Time spent getting to/from suppliers
I will charge you cost price for the materials
How about you pay me for labour at the same rate per hour as you get.


It's amazing how many BMW/Porche/Smart 4x4 drivers suddenly plead pitiful salaries.

I was caught out by one of the above who had promised to pay when I'd finished. He renaged hoping to get a better price. I cut it in two and put in on the fire in front of him. After that he pays a material cost & deposit up front for any work he wants.


I would rather, and have frequently, given them away to friends as presents.


As yet I've not been paid for photography. I don't think I'm good enough yet, but I'm happy to accept invitations to birthday parties and weddings from friends and my prints are given in friendship.

regards
Bernard

Comment by Frogherder posted on Work for nothing? at 03/02/2012 - 00:18

Frogherder
From my point of view I'd also thought of river courses (I live less than 1/2m fron the R.Trent, but as I've injured my back a little travelling to the source/estuary is not on at the moment.
Rodgets Thesaurus wasn't a great deal of help in coming up with an alternative, so food it was.
Thinking that, as it's a festive time, every one would be doing the banquettes I chose the alternative.

Not wishing to appear to be Xenophobic in any way at all I felt our Canadian cousins had to have some competition iven if I'd already worked out that JA was likely to win.

regards
Bernard

Comment by Frogherder posted on Monthly Competition #6- "Three Courses" Entries at 02/02/2012 - 14:24

Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo