stu49

Joined: 20th September 2009

All Forum Comments

Topics Created Topics Contributed Forum Comments Photo Comments

All Forum Comments

stu49
haydnw wrote:
Thanks for the replies guys,

Free sounds good to me Peter, I'll give the podcasts a try first
Amazon are doing Scott Kelby's book on LR2 for £14+ (a snip). Great book, as are his PE5 and CS4 books, which I also have

Comment by stu49 posted on Lightroom 2 at 26/11/2009 - 22:28

stu49
thoughton wrote:
SteveF this link might be of interest:
http://brisbanesecondhandbooks.com/photography
Very helpful, thank you

Comment by stu49 posted on Optical trigger !? at 20/11/2009 - 14:12

stu49
SteveF wrote:

I use a Sunpak Auto36DX. In manual you can adjust the output from full down to 1/16. They do come up on eBay - that's where I got mine. And safe to use on your Pentax DSLR.

Other Sunpak models offer the same facility. If there's a photo of the back of the flash in the listing you can see the slider and associated markings. Good hunting.


Unfortunately, MOST people don't show the back !! It would be a lot easier, and more helpful, if they did

Comment by stu49 posted on Optical trigger !? at 20/11/2009 - 14:04

stu49
hamiltonsmith wrote:
You can tether to the Pentax software
Using LR but can't find software on any Pentax site !?? any help ?

Comment by stu49 posted on Tethered Shooting !? at 19/11/2009 - 19:59

stu49
Anyone know how to set up tethered shooting ?? Any software required ?

Comment by stu49 posted on Tethered Shooting !? at 19/11/2009 - 19:16

stu49
digikid-tv wrote:
I setled on the Vivitar 283 as they are very cheap, plentiful and powerful.

They need the VP1 varipower module to operate in a fully variable mode, this plugs in in front of the flash in place of the sensor. The range available is from full power down to about -5.5 stops.

Unfortunately this module is rare and thus relatively expensive to buy nowadays. However it only contains a 100k ohm potentiometer, a series resistor of 3.9k ohms and a 200 picofarad capacitor and I have successfully modified two of my units by mounting these parts in a small plastic box mounted in place of the sensor.

I am abroad at the moment but could send more details when I get home next week.
Thanks for that, more details would be good

Comment by stu49 posted on Optical trigger !? at 19/11/2009 - 19:01

stu49
digikid-tv wrote:
stu49 wrote:
digikid-tv wrote:
I have been using a pair of Seagull SYK3 triggers for 3 years now with my old Vivitar 283 flashguns, trigger voltage measured at 270 volts, with no problem. In fact I have just increased my collection of this combination by 2 more sets to use as inexpensive studio strobes.
Just don't forget and pop it on your camera one day

Having said that our cameras use a similar (if not identical) circuit to these Opto switches, so should survive I'm not trying it out on mine though
I have labelled all my old flashguns with the measured trigger voltage so that hopefully (senior moments permitting) this does not happen!
Just done the same

I know the 283/285 have manual settings, but what else is out there with at least 1/16. 1/4 and full options. Finding it difficult to find any manual flashes (CHEAP and probably old, of course). Don't need the fancy stuff (TTL, P-TTL, Auto, etc.), but so many on ebay don't give a reasonable description of what they can do, so I need to know the model numbers ! Hope u can help

Comment by stu49 posted on Optical trigger !? at 19/11/2009 - 17:59

stu49
MattMatic wrote:
Most optical triggers use an SCR device, as far as I know.
There's always the possibility that it could fry the optical slave - but that's much, much cheaper than frying a body

Matt
As u say Matt ; safer than frying my K10 just wondered if anyone knew the rated voltage

Comment by stu49 posted on Optical trigger !? at 19/11/2009 - 17:44

stu49
digikid-tv wrote:
I have been using a pair of Seagull SYK3 triggers for 3 years now with my old Vivitar 283 flashguns, trigger voltage measured at 270 volts, with no problem. In fact I have just increased my collection of this combination by 2 more sets to use as inexpensive studio strobes.
Just don't forget and pop it on your camera one day

Having said that our cameras use a similar (if not identical) circuit to these Opto switches, so should survive I'm not trying it out on mine though

Comment by stu49 posted on Optical trigger !? at 19/11/2009 - 17:41

stu49
K10D wrote:
I built something similar to this for an old Elinchrome.
The TIC106D is the standard choice and readily available.

Another more flexible circuit
The Opto isolator is 100% safe.

Regards
Thanks for that, I like the sound activated one, might build that !?
Being an electronics engineer, I know what's inside them but as they're sealed I can't see which output device they use, so have no idea of the max operating voltage. Guess I'll just have to try it and see

Comment by stu49 posted on Optical trigger !? at 19/11/2009 - 17:37

Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo