All Forum Comments
Comment by golfdiesel posted on printservice icc profile at 23/12/2006 - 20:42
For those interested the profile in question is here: http://www.vakprint.nl/hst/v11p07d/vakprint.nsf/all/A00FDB47340DC686C12571F5003DEC6D/$FILE/NL_Befo_dlab2_CA-TypeII_21082006.icc
Comment by golfdiesel posted on printservice icc profile at 17/12/2006 - 19:58
Comment by golfdiesel posted on printservice icc profile at 03/12/2006 - 19:03
They offer a icc profile on their website. Should I in this case embed this icc profile when doing the RAW conversion instead of the camera profile?
Comment by golfdiesel posted on printservice icc profile at 03/12/2006 - 18:08
Heat can do strange things to all electronic components.
I have read somewhere that someone used a cooling element which you use in your coolbag or coolbox when you go to the beach. He attached it to the back of the camera to cool it down. This was for astronomy pictures with very long exposures. The problem with cooling this way is the risk of condensation.
Ideally you should have an active cooling system which takes into account the dewpoint and such, but that will be impossible to use on a portable system like a camera...
Comment by golfdiesel posted on Reciprocity Failure ? at 03/12/2006 - 12:29
I would think getting an old pentax compatible flash which has a manual mode is a good idea. Just put it into the lowest possible output and even put a diffuser on it so that you get as little light out of it, just enough to trigger the slave flashes.
Comment by golfdiesel posted on Setting off studio flash using the in-built camera flash at 03/12/2006 - 15:40
Did they change any other things as well?
There is one thing I would like, if they would offer a printed manual for sale then I would be interested. There is so much to take in account in terms of settings and it takes a lot of reading.
Comment by golfdiesel posted on Silkypix DS 3.0.3 Preview at 03/12/2006 - 12:18
I do not want to buy a bigger camera like 645. If you do buy it. I prefer to remain to 35mm SLR.
One of the most important advantages of Pentax is compatibility. The most important. You can find anything and put it on a Pentax body. Manual focus or Auto focus, Pentax, Carl-Ceiss, Chinon, Tamron, Tokina, Vivitar, etc etc.
Pentax is a serious company and it is not going to put the moter on the lenses.
There are lenses that cost millions. Could you imagine such a lens with a broken motor?
/Remco
Comment by golfdiesel posted on Poll - who would £1000 for a full frame K10D? at 13/12/2006 - 20:41
I WOULD BUY A FULL FRAME PENTAX FOR 1000pounds, but I want this body to be compatible with TTL Flashes and all the lenses by Pentax.
If it becomes true, please send me a message.
I got tired to wait Pentax to do the right things.
Why on earth should Pentax support 20 year old technology. Backwards compatibility is nice, but in the end it will cause a lot of problems because it can slow down development.
Just look at Microsoft, they still have to keep their OS backwards compatible which causes a lot of problems. Sometimes a company needs to draw a line and start fresh.
Pentax has started a gradual changeover with the K10D, they support lenses which use the motor in the body and they support the newer HSM lenses. In a few years Pentax will introduce a body which does not support the lenses without a motor in the lens.
Comment by golfdiesel posted on Poll - who would £1000 for a full frame K10D? at 13/12/2006 - 13:47
For us the images are: 10x15, 20x30, etc. This is all 2:3 the same as the sensor when I'm right.
35mm film is 24x36mm, allso 2:3.
Why then change the sensor aspect ratio if it is only needed for people who use imperial measurements (does anyone know what percentage of the world use imperial measurement?)
Comment by golfdiesel posted on Poll - who would £1000 for a full frame K10D? at 29/11/2006 - 12:10


If I look at the printed pictures and you pick which one looks the best it is the sRGB one and not the one which was converted to the icc profile of the printshop...