Frogherder

Joined: 19th February 2009

All Forum Comments

Topics Created Topics Contributed Forum Comments Photo Comments

All Forum Comments

Frogherder
Quote:
Anybody know how to get into a Super-Tak 55 f/2 which won't stop down at all
Post it down to me with a suitable cheque - I'm on a roll


No resposibility can be acepted for springs or ball bearings flying off in random directions. Or as the banks say the value of your investment can also go down

Bernard

Comment by Frogherder posted on M42 Fujinon Lens at 16/05/2012 - 23:26

Frogherder
Thanks guys,
I can sit back with a smug grin on my face. Testing will be tomorrow (if I can find time) or weekend. Initial tests (@1. show that it focuses on clouds so that's sorted the infinity spot. Likewise 0.45m is pretty well correct (as near as I can tell) and everything runs smoothly.

Just to make you green I'll let on that the total monetary cost to me was £1.99, so I reckon I've got a bargain.

Even if it turns out to be a turkey after testing - I've learnt someting on the way.

regards
Bernard

Comment by Frogherder posted on M42 Fujinon Lens at 16/05/2012 - 23:21

Frogherder
Basicaly this one comes apart by turning the focus to minimum (0.45m), this exposes the 3 screws shown in pic#1.
Loosen these screws until flush enables the front ring to be unscrewed.

This reveals 4 dome headed screws with bronze washers which hold the focusing barrel onto the lens/aperture assembly (top left and right in the last pic).

At this point the lower index ring can be removed by loosening the 3 screws until flush and lifting off (Holding down the aperture setting ring to avoid losing the ball bearings - there appear to be 2)

This reveals a further 3 countersunk screws which can be removed to release the entire aperture mechanism (top centre) and the setting ring.

The pin is then removed by loosening 2 dome headed screws which hold the bell crank lever assembly (about 2'o clock in the top centre item).

Put about 3-4mm of sleeving over the pin (cut from the shaft of a cotton bud) and carefully re-assemble in reverse order.

regards
Bernard

Comment by Frogherder posted on M42 Fujinon Lens at 16/05/2012 - 20:04

Frogherder
So far so good

[IMG]http://i1236.photobucket.com/albums/ff444/Frogherder/IMGP1211.jpg[/IMG]

Bernard

Comment by Frogherder posted on M42 Fujinon Lens at 16/05/2012 - 15:28

Frogherder
Spot on, the right hand one moves with the aperture ring.

The lower set of screws refered to earlier must have something to do with it, but once these screws are out it doesn't want to slide or unscrew and is not releived in any way. In fact the only movement is that of the focusing helicoid and thats not even part of the bit with the screws in.

I'm tempted to follow the frontal attack and see if this removes the lens/aperture as a complete assembly. If so, with the actuation of the aperture, effectively disabled I might be able to attack it through the rear hole. At least there would be some tweezer room and I could see what I'm doing a bit better.


Have already rejected the glue idea for the same reasons.

I did consider cutting of the pin flush then tapping the hole and effectively replacing the pin with a long grub screw, but the piece inside would still be too long to remove

regards
Bernard

Comment by Frogherder posted on M42 Fujinon Lens at 16/05/2012 - 14:38

Frogherder
Algi, I was only repeating what I was told some 40 years ago, you tend to believe an awful lot of things at that age.

I think maybe what they might have been getting at was the centre to edge distances becoming more pronounced the nearer the object is. But I take your point the helicoid is essentially an extension tube

regards
Bernard

Comment by Frogherder posted on Lenses and focal leangth. at 16/05/2012 - 14:23

Frogherder
Assuming the lens is set to infinity then 50mm of extension (tubes or bellows) would give an image the same size as the object. Setting the lens to 0.45m would give a magnification of 1.125 and a focusing distance as low as 94mm.

However I'm led to believe that lenses perform best when set to infinity with regards to distortion. How true this is I've no idea.

regards
Bernard

If any one want the maths I can provide the formulae

Comment by Frogherder posted on Lenses and focal leangth. at 16/05/2012 - 13:50

Frogherder
Quote:
I'm new to photography. I've bought a K-5 with the 18-55mm kit lens. The camera's going to be used by me and my wife
Despite what's been suggested about various lenses (all very good in their way) I would suggest that you first experiment with the 18-55m which comes with the camera.

I don't think anyone would mark this lens down and after say 3 months you will be in a much better position to descide what its limitations are for you and expand your lens aquisitions based on 'need' rather than 'might need'.

I started with a 50mm lens and it was probably 10 years before I bought a 200mm and 28mm (zooms were not generally available then)

Regards
Bernard

Comment by Frogherder posted on One "all-in-one" lens for beginner at 16/05/2012 - 13:36

Frogherder
Thanks Stuey - So far I've been lucky, the last one I took apart ejected a small ball bearing which bounced off my monitor and landed on the rug below my feet. Magnet in hand I managed to locate and retrieve it. If it had missed the monitor it would probably have finished up in miscellaneous 'junk' behind my desk.


Algi - I look into that link

Bernado - not sure that your deductions are correct. The slot and hole were cut prior to anodising. The hole is little more than a countersink.


Further examination suggests that the entire aperture assembly is part of the sliding lens assembly, so I'm wondering if this lens was assembled through the front as when I squint through the back there are 2 long rods (20mm?) which engage with the aperture mechanism
[IMG]http://i1236.photobucket.com/albums/ff444/Frogherder/12051613165816287312a.jpg[/IMG]

Bernard

Comment by Frogherder posted on M42 Fujinon Lens at 16/05/2012 - 13:25

Frogherder
Thanks Algi, I had already googled and found several references to 'fixing' the pin ranging from superglue to pushing it in until it jammed. What I would like to do is slide a piece if tubing over the pin, but this requires me to get at it and so far I've only managed to open the front and I'm bright enough to realise that if I disturb the lenses I've still got to get past the aperture and I'm not sure whether either of these would be a good idea.

Working on the priciple that someone put the lens together (albeit probably with fingers half my size) I should be able to take it apart, I've done it with several lenses in the past but this one is foxing me.

So having looked on other forums I thought I'd ask if any one here as done the same.

I have 2 M42 to PK adapters - one with an external flange, but this loses infinity focus; and a second which fits flush with the camera, which enables infinity fousing.
I didn't know about the internally flanged adapter, I'll have to check that out.

regards
Bernard

Comment by Frogherder posted on M42 Fujinon Lens at 16/05/2012 - 12:31

Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo