All Forum Comments
Comment by Frogherder posted on What microphone for video? at 25/05/2011 - 13:39
In 3 years of shooting digital I've taken almost 6000 photos (many of which are scrap or only of interst to me). I'd hate to tot up the cost of all those 6x4 prints even from printhouses that give away a free film.
Over that previous 40 years I still had oodles of scrap pics which were paid for up front and now I only pay for the ones that I need and think are really good. Also relatively speaking digital cameras are much cheaper than their film counterparts were.
Comment by Frogherder posted on Film Versus Digital at 25/05/2011 - 13:29
I was also going to add other queries such as :-
"Has the circle of confusion been replaced by a single pixel"
but thought better of it
regards
Bernard
Comment by Frogherder posted on Lens Formulae at 25/05/2011 - 13:14
regards
Bernard
Comment by Frogherder posted on capture insects in flight? at 25/05/2011 - 13:04
You have too much time on your hands.
Get out there and take photographs and leave such cogitations to the lens designers.
The answer is probably stop fretting over nothing (that you can control anyway) and concentrate on pressing the shutter more, but my curiosity is awoken.
Bernard
Comment by Frogherder posted on Lens Formulae at 25/05/2011 - 12:57
I've found something else to worry my little grey cells.
My K10D 18-55 lens focuses down to 250mm and the specs says this is a magnification of 0.34 with the lens at 55mm. So far so good.
I've measured the 250mm to be from the target to just in front of the eyepiece adjustment lever (probably the sensor plane). My film camera did much the same.
Now come the query :-
Lens formulae gives
1/v + 1/u = 1/f (where u = target distance from centre of lens; v = image distance from centre of lens; and f = focal length)
M = u/v (where m = magnification)
So by inference u + v is equal to the target to image distance (ignoring the internodal space which would increase the distance anyway)
So is the focusing distance expressed as 250mm equal to u+v.
If so the above formulae give a target distance of 186mm and image distance of 63mm and to compound the query further the focal length comes out as 47mm
Whats happening?
regards
Bernard
The answer is probably stop fretting over nothing (that you can control anyway) and concentrate on pressing the shutter more, but my curiosity is awoken.
Comment by Frogherder posted on Lens Formulae at 25/05/2011 - 12:50
Interesting to note that I never gave it a moments thought in the days of film.
At the end of the day I'm probably the weakest link in my photographic exploits - not sure whose avatar catch phrase it is but "I am trying hard - honest"
John - I'm a bit like the ancient mariner as regards AP - I stop maybe 1 in 3 and that's only if there's any left when we go shopping on Fridays.
Smeggypants - That looks more suited to balancing tyres than camera lenses
Bernard
Comment by Frogherder posted on Measuring before Adjustment at 25/05/2011 - 12:31
(the bit about 1.414 etc loses me
So for every 1.414mm up a 45 deg slope you travel the vertial and horizontal distances are each 1mm
regards
Bernard
Comment by Frogherder posted on Measuring before Adjustment at 23/05/2011 - 17:02
I placed it further in the workshop to avooid the backlighting. Lighting on all is from a skylight.
[IMG]http://i1236.photobucket.com/albums/ff444/Frogherder/IMGP5892.jpg[/IMG]
Looks OK to me so I don't think I'll be fiddling in debug mode
(incidentally page 4 of the blog doesn't say " MODSET.TXT" it uses a numerical value rather than TXT and doesn't provide a number for a K10D with 1.31 software - or have I found the wrong info?)
regards
Bernard
Comment by Frogherder posted on Measuring before Adjustment at 23/05/2011 - 16:52
I used the large triangle to indicate the centre and focused with the selector set to point when the camera beeped with the small red square in the viewfinder on the centre line I fired the shutter.
Is that the right thing to do?
The camera was square to the board which was tilted back at 45 deg.
Camera was 1 metre away from centre of board
Small divisions are 1.414 separation ie 1mm in Horizontal plane
Lens appears to focus abot 20-30mm back
Bernard
Comment by Frogherder posted on Measuring before Adjustment at 23/05/2011 - 15:11


No one mentioned "noise cancelling microphones" - could be a usefull variation to consider if you go to noisy events. Google will provide any number of links
regards
Bernard