All Forum Comments
Comment by andy_bell posted on Help with lense choice please at 09/03/2015 - 20:29
Quote:
By Pentasonic49
Having the same fault on two cameras is a disaster. I looked at my K5, and the mechanism is the same as all the autofocus cameras including the film cameras. The spring which keeps the drive dog out is linked to the lens removal button as well as the autofocus lever/slider. Try switching to autofocus without a lens and press the lens lock button several times. this might free the drive dog. Hold the camera lens throat downwards to see if the dog drops down. The coil spring can just be seen looking at an oblique angle across the lens throat lined up with the red spot (use a small light source). I don't think the spring is stressed enough to ever break, there is some other fault. If I had this problem, I would get an old, non working autofocus film body to take the lens mount off for practice and possible spares. Also if the lens locking pin is held down by not fitting in the hole in the lens, the drive dog is also depressed.
And my Response......
Pentasonic, Brilliant!
I have just checked the 2 K5 bodies and found.....
One body was just, and I mean just, off the continuous AF setting, thus holding the drive pawl back far enough so as not to engage.
The second body I think must have had a bit of grit in there as after a couple of "toggles" with the lens release button everything is fine.
You have just saved me the pain of sending the bodies needlessly for repair!
Thanks
I think that I can post this in the "live & Learn" column......
At least my 2 K5's are not crocked....and I've found something to check and pay more attention to....
Andy
Comment by andy_bell posted on No AF (Screw drive Lenses) at 09/03/2015 - 20:14
I checked what you said and found the drive Pawls to be free,
it really does appear to be a weakening of the springs which push the drive mechanism forwards, they even feel weaker in comparison to the one on the K3 & 1.4x converter
Andy
Comment by andy_bell posted on No AF (Screw drive Lenses) at 06/03/2015 - 22:09
always just after you have ordered some.......
Comment by andy_bell posted on Genuine Pentax Body Caps at 06/03/2015 - 20:24
Andy
Comment by andy_bell posted on Genuine Pentax Body Caps at 06/03/2015 - 20:13
Andy
Comment by andy_bell posted on Genuine Pentax Body Caps at 06/03/2015 - 19:38
You were right
Just checked again & the lens drive is recessed, I suppose that is because most of my lenses are SDM or HSM & there is no locating hole for the drive shaft so the spring looses its tension therefore won't engage in the screw drive lens' oriface,
Looks like a trip to Pentax is in order for the two K5 bodies
Comment by andy_bell posted on No AF (Screw drive Lenses) at 06/03/2015 - 17:25
but i'll have a look at the drive coupling to see where its sitting..
I can compare it with the K3 which is working....
Comment by andy_bell posted on No AF (Screw drive Lenses) at 06/03/2015 - 15:14
No, both of the screw drive lenses I own work fine on the K3, neither will work on either of the K5's
I'll have to borrow the wife's 55-300 DA I think that is a screw drive.....and see if that will work..
Comment by andy_bell posted on No AF (Screw drive Lenses) at 06/03/2015 - 13:05
Andy
Comment by andy_bell posted on D-LI90 3D printed battery covers at 06/03/2015 - 12:35


Pro's
Its f/2.8,
Its all internally Zoomed & focussed (doesn't grow on Zoom or Focus)
Has the fast, accurate HSM, possibly more reliable than the SDM on the 60-250
Is very quiet during focussing...
Switchable Image stabilization
Solid as a rock quality build....
Cons...
It is a bit on the large side
Not as 'WR' as the 60-250 perhaps
Andy