Sucessfull (ish) fungus cleaning

pnjmcc
Posted 28/01/2010 - 02:43 Link
Hi all,

After reading several posts about these Takumar lenses I thought I should probably get one to have a play with myself as they seem to be cheap enough on ebay.

So after scouring ebay for some cheapies I found an acution for a 135 3.5 and a 55 f2 attached to a Spotmatic SP500. All in a swanky looking case with an off camera flash bracket and some M42 extention tubes thrown in for good measure.

So there I was looking forward to trying these new (to me) lenses and when they finally turned up the 55-f2 was opticaly clean with signs of heavy use, luckilly it still felt smooth and the iris was snappy and clean, the 135 was in its original leather case with both front and rear caps looking totally unused I was very happy until I looked through it, there was some spidery tendrils of fungus comming in from the edges of the glass.
Feeling a bit gutted as the SP300 has 'issues' too I turned to google to see what I could find out about removing fungus before I binned it, I came across this site. (scroll though cause he dismantles a few lenses)

OK so the lenses he talks about aren't exactly the same but the principles of cleaning and the tools he used are (and he shoots with a K10 ). So using a pair of dividers, a set of watch scewdrivers, a sink plug, some cold cream, zippo fluid and lense cleaning fluid and this image of a fully dismantled 135 f3.5. I magaed to desmantled and reassemble the lens and remove the fungus, with no problems other than a slightly chewed screw head.

Far easier than I thought it would be.

I just need a decent M42 to K adapter now to test the lenses properly, ( the one I have stands to far out more like a macro extension) and a few spare parts for the SP500.

Regards
PaulM
All cameras are equal but.....
Some are more equal than others
Mike-P
Posted 28/01/2010 - 06:51 Link
I hope you went after the Ebay seller.
Technoblurb
Posted 28/01/2010 - 08:34 Link
That's a nice little tutorial, it has been bookmarked for future use.

Regards

Graham
Dangermouse
Posted 28/01/2010 - 08:47 Link
I've used vinegar on a cotton bud to clean fungus before now, all you need is a mild antiseptic that won't harm coatings. Rescued three 50mm lenses that way!

I do have another lens with some worrying specks (hope they're just dust) but I can't persuade the front to unscrew and it's a bit too valuable to risk pressing harder. Instead, I stored it on the radiator for a couple of weeks to make sure it was thoroughly dry and it now lives in a lens case with a sachet of silica gel.
Matt

Shooting the Welsh Wilderness with K-m, KX, MX, ME Super and assorted lenses.
pnjmcc
Posted 28/01/2010 - 11:05 Link
Mike-P wrote:
I hope you went after the Ebay seller.
Mike, if it had cost more I would've made a fuss but for the price I paid I got a good enough deal.

Technoblurb wrote:
That's a nice little tutorial, it has been bookmarked for future use.

Regards

Graham
Glad it as of some help Graham

Dangermouse wrote:
I do have another lens with some worrying specks (hope they're just dust) but I can't persuade the front to unscrew and it's a bit too valuable to risk pressing harder. Instead, I stored it on the radiator for a couple of weeks to make sure it was thoroughly dry and it now lives in a lens case with a sachet of silica gel.
If you use the rubber plug method it really is simple. Just apply more more pressure. Or for more stubborn rings and if you can find a replacement on ebay drill two small holes in the ring and use the holes to twist it out.

I will add some pics of this 135 lens asap

Regards
PaulM
All cameras are equal but.....
Some are more equal than others
Edited by pnjmcc: 28/01/2010 - 11:06
Dangermouse
Posted 28/01/2010 - 12:10 Link
Problem is, this lens doesn't have a finishing ring around the outside of the glass, just a metal collar about half a millimetre wide that screws into the filter thread to hold the front element in. It does have a couple of notches in but I'm scared to try using a couple of screwdrivers to turn it in case they slip. As it's a Pentax-A 200mm f4 I don't want to risk damaging the glass - they're not exactly easy to come by!

With something like a £5 50mm f2 I'm less worried, and in any case they have the finishing ring so you can get a grip with a bit of rubber. I use the strap from one of those "boa" jar openers.

Gareth, that 50mm will be an absolute doddle to fix. You just unscrew the finishing ring and then unscrew the front element group. You won't need to adjust anything, just refit them a little more than finger tight.
Matt

Shooting the Welsh Wilderness with K-m, KX, MX, ME Super and assorted lenses.
Edited by Dangermouse: 28/01/2010 - 12:12
mowog
Posted 28/01/2010 - 12:25 Link
NO.!... Don't drill!.

Go to the Pound shop and buy a pack of double sided sticky pads. (you get hundreds for a quid). Cut a couple into strips. about 20mm x 5mm. Stick four or five of those around the name ring and use a rear lens cap of suitable size to stick on the pads. Then just unscrew. The pads peel off easily, afterwards. .
No man is worth his salt, who has not been banned from at least one Forum, and two Flickr groups.

Mowog.
Edited by mowog: 28/01/2010 - 12:26
Dangermouse
Posted 28/01/2010 - 14:25 Link
The finishing ring is what I call the bit with the "Pentax-M 50mm" lettering on, it's just screwed into the filter thread. Once you've removed that then the front element group can be unscrewed (conventional thread, unscrews anticlockwise). You will need something to fit into the little notches and twist it - I did use a couple of small screwdrivers last time but there's a risk of them slipping if it was tightened by the Asahi works Sumo squad!

I've just bought a proper lens spanner for £15 on ebay, it should turn up in the next day or so and I'll be able to sort the 200mm f4 out. It's basically a couple of steel bars with a pair of angled prongs attached, you move these to the right width on the bars, tighten them with a couple of small bolts, then put the prongs into the notches and use it to unscrew the component. Due to the design it cannot easily slip and damage the glass.
Matt

Shooting the Welsh Wilderness with K-m, KX, MX, ME Super and assorted lenses.
pnjmcc
Posted 28/01/2010 - 22:55 Link
mowog wrote:
NO.!... Don't drill!.

Go to the Pound shop and buy a pack of double sided sticky pads. (you get hundreds for a quid). Cut a couple into strips. about 20mm x 5mm. Stick four or five of those around the name ring and use a rear lens cap of suitable size to stick on the pads. Then just unscrew. The pads peel off easily, afterwards. .
Thats a good hint mowog,

I would only drill as the last resort if your desperate to get the ring off.

Gareth, mine came off quite easily, it took a bit of downward pressure on the sink plug to keep it gripping in to the ring though.
I would suggest try cleaning the threads with a toothpick and maybe try a very small amount freeing oil applied via toothpick or even try tightening it before you loosen it.

Good luck.

Regards
PaulM
All cameras are equal but.....
Some are more equal than others
womble
Posted 28/01/2010 - 23:04 Link
If the lens is worth more than a few quid I'd send it to Alan Marlow (A.M. Technical Services). He serviced a few lenses for me and did a sterling job.

Personally, I am cack handed on a scale of cack-handedness my father (a very practical man) couldn't believe. I'd probably get the lens apart but in what condition is anyone's guess!

Cheers, K.
Kris Lockyear
It is an illusion that photos are made with the camera… they are made with the eye, heart and head. Henri Cartier-Bresson
Lots of film bodies, a couple of digital ones, too many lenses (mainly older glass) and a Horseman LE 5x4.
pnjmcc
Posted 29/01/2010 - 08:53 Link
womble wrote:
If the lens is worth more than a few quid I'd send it to Alan Marlow (A.M. Technical Services). He serviced a few lenses for me and did a sterling job.

Personally, I am cack handed on a scale of cack-handedness my father (a very practical man) couldn't believe. I'd probably get the lens apart but in what condition is anyone's guess!

Cheers, K.
Kris,

I would not have attempted this on any auto focus lens or anything that cost me over £50. I only tried it because I considered it a disposable item. I must confess it was a lot more simple than I was expecting!

Regards
PaulM
All cameras are equal but.....
Some are more equal than others
womble
Posted 29/01/2010 - 08:56 Link
I was thinking more of Dangermouse's A series 200mm which is probably worth a little more than that!

Lots of people do happily do this little job, it just isn't for me!

Best wishes, K.
Kris Lockyear
It is an illusion that photos are made with the camera… they are made with the eye, heart and head. Henri Cartier-Bresson
Lots of film bodies, a couple of digital ones, too many lenses (mainly older glass) and a Horseman LE 5x4.
Dangermouse
Posted 29/01/2010 - 12:04 Link
Yep, I unscrewed the front thing, but only the very front element fell out. At this point I decided to put it back together and leave well enough alone! Think I got away without much dust getting in. A few quick test shots showed no harm done.

The specks don't seem to affect image quality and the lens lives in a case with a bag of silica gel, so I doubt it'll get worse. If it does, I'll look at prices for a professional strip down and clean.
Matt

Shooting the Welsh Wilderness with K-m, KX, MX, ME Super and assorted lenses.
womble
Posted 29/01/2010 - 13:16 Link
Alan charged me 30 quid for a CLA, might be a little more with fungus. You might be better off storing the lens somewhere light and airy and letting some UV get to the fungus. Sealed in cases is not so good unless you are very fussy about changing the silica gel on a regular basis.

Best wishes, Kris.
Kris Lockyear
It is an illusion that photos are made with the camera… they are made with the eye, heart and head. Henri Cartier-Bresson
Lots of film bodies, a couple of digital ones, too many lenses (mainly older glass) and a Horseman LE 5x4.
Dangermouse
Posted 29/01/2010 - 15:36 Link
What's the best way to do that - leave it on a windowsill with the lens cap off for a while?

I was about to say I'd put a spare UV filter on to protect the front element, but that would rather miss the point!

Edit, just emailed Alan for a quote. Even if it costs me another £50 I'm doing well. I paid £99 for the lens and the last one I saw on ebay was priced at £350 (admittedly by a well-known seller with an interesting idea of the value of lens caps, but still!)
Matt

Shooting the Welsh Wilderness with K-m, KX, MX, ME Super and assorted lenses.
Edited by Dangermouse: 29/01/2010 - 16:03

Add Comment

To leave a comment - Log in to Pentax User or create a new account.



Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo