K10d af not working
Posted 14/11/2012 - 11:47
Link
The K10D is way, way out of warranty by now, so why not return it directly to JPS for a quotation?
You'll find the address on the Pentax UK website: http://www.pentax.co.uk/en/service-centre.html
You'll find the address on the Pentax UK website: http://www.pentax.co.uk/en/service-centre.html
Best regards, John
Posted 14/11/2012 - 12:08
Link
I know that my camera is "way,way out of warranty" that’s why I said "I am out of warranty now" lol ,but thanks for your response
I was hoping somebody would have had the same problem and knew a fix SRS said at the time they simply upgraded the firmware, but as far as i am aware it came back with the same firmware version as when it went to them. i have read about solving AF problems using debug mode but they were concerning AF not focusing properly ,I wondered if anybody had an idea for a DIY fix?
I was hoping somebody would have had the same problem and knew a fix SRS said at the time they simply upgraded the firmware, but as far as i am aware it came back with the same firmware version as when it went to them. i have read about solving AF problems using debug mode but they were concerning AF not focusing properly ,I wondered if anybody had an idea for a DIY fix?
Posted 14/11/2012 - 14:18
Link
You could try loading the firmware again?
One day you'll find, 10yrs have got behind you.
Posted 14/11/2012 - 18:36
Link
Sorted now thanks got the help needed from http://www.pentaxforums.com
Posted 15/11/2012 - 09:12
Link
Yesterday, 02:06 PM #2
ismaelg
Site Supporter
ismaelg's Avatar
First step is to make sure the contacts are clean. Carefully clean the contacts in the body mount (and in the lens as well to make sure). You can use an eraser or a very fine grit sandpaper GENTLY. Check to see if any of the contacts look damaged or different.
Hope this helps.
Thanks,
Yesterday, 02:27 PM #3
JimJohnson
Site Supporter
JimJohnson's Avatar
In addition to cleaning the contact points, make sure all the screws for your body's mounting flange are snug. When mounting a lens, hold in the release button, turn the lens all the way into the mount, release the lens release button and turn the lens backwards in the mount until the lock clicks. If you still do not have full lens functioning, try slowly rocking the lens slightly clockwise / counter-clockwise and watch to see if you get a connection.
webba
New Member
Join Date: Nov 2012
Posts: 2 | Likes: 0
Original Poster
Well I combined the advice given by both ismaelg and Jim Johnson and it worked I honestly cant say which as I did them both at the same time. but I would like to thank both of you
ismaelg
Site Supporter
ismaelg's Avatar
First step is to make sure the contacts are clean. Carefully clean the contacts in the body mount (and in the lens as well to make sure). You can use an eraser or a very fine grit sandpaper GENTLY. Check to see if any of the contacts look damaged or different.
Hope this helps.
Thanks,
Yesterday, 02:27 PM #3
JimJohnson
Site Supporter
JimJohnson's Avatar
In addition to cleaning the contact points, make sure all the screws for your body's mounting flange are snug. When mounting a lens, hold in the release button, turn the lens all the way into the mount, release the lens release button and turn the lens backwards in the mount until the lock clicks. If you still do not have full lens functioning, try slowly rocking the lens slightly clockwise / counter-clockwise and watch to see if you get a connection.
webba
New Member
Join Date: Nov 2012
Posts: 2 | Likes: 0
Original Poster
Well I combined the advice given by both ismaelg and Jim Johnson and it worked I honestly cant say which as I did them both at the same time. but I would like to thank both of you
Posted 15/11/2012 - 12:21
Link
Cheers Webba. It just completes the thread and if anyone else is in the same boat and search's then hopefully your experiance will help out
One day you'll find, 10yrs have got behind you.
Posted 15/11/2012 - 14:39
Link
webba wrote:
Carefully clean the contacts in the body mount (and in the lens as well to make sure). You can use an eraser or a very fine grit sandpaper GENTLY.
Any thoughts on best way to clean contacts?Carefully clean the contacts in the body mount (and in the lens as well to make sure). You can use an eraser or a very fine grit sandpaper GENTLY.
I don't think I would take sandpaper of any gauge anywhere near my K10.
I had seen about using erasers (apparently Canon used to recommend this approach but don't now) but also a lot of warnings about using them.
What most seemed to recommend was isopropyl alcohol on a barely damp microfibre cloth or cotton bud.
Posted 15/11/2012 - 14:41
Link
A clean dry cloth should be all that's necessary, to remove any contamination. Slightly damp if needed, but no more than that.
Best regards, John
Posted 15/11/2012 - 15:12
Link
I would be cautious of anything coarser than typing/photocopy paper. Any dust, however fine, that you make will make a beeline for the sensor.
Then you have a second problem
regards
Bernard
Then you have a second problem
regards
Bernard
Posted 15/11/2012 - 15:34
Link
I normally use a lens cloth, dabbed on my tongue if I need a bit more cleaning power.
One day you'll find, 10yrs have got behind you.
Posted 15/11/2012 - 19:33
Link
Please be warned, what ever else you do, never ever use sand paper on electrical contacts, be it on your camera or any other item/appliance.
Take care.
Take care.
Chris R.
I. El. (Eng). (Rtd).
I. El. (Eng). (Rtd).
Posted 16/11/2012 - 12:26
Link
ChrisR wrote:
Please be warned, what ever else you do, never ever use sand paper on electrical contacts, be it on your camera or any other item/appliance.
Take care.
What he said!
Please be warned, what ever else you do, never ever use sand paper on electrical contacts, be it on your camera or any other item/appliance.
Take care.
Getting there! Thanks to you guys
Pentax K3ii, Pentax K10d, Kit lens ( 18-55mm ), 50mm f1.7 lens, Tamron 70-300mm lens, Prinzflex 70-162 manual lens, Various old flashes.
Pentax K3ii, Pentax K10d, Kit lens ( 18-55mm ), 50mm f1.7 lens, Tamron 70-300mm lens, Prinzflex 70-162 manual lens, Various old flashes.
Posted 16/11/2012 - 15:57
Link
What they both said , sand paper is for sanding wood ,,,jeff... lens contacts clean with a lenscloth
Add Comment
To leave a comment - Log in to Pentax User or create a new account.


49 posts
16 years