Measuring before Adjustment
Posted 23/05/2011 - 13:38
Link
Borrowed from elsewhere:
The method is based on the information published here:
http://www.pentax-hack.info/documents/blog.php?page=1
1. Use a notepad to create a file MODSET.TXT with the following line:
[OPEN_DEBUG_MENU]
followed by a new empty line.
2. Save the file on the root directory of your SD flash card (either use the USB cable to connect to the camera or an external SD flash reader).
Now you are ready to Enable/Disable the Debug mode on the best camera in the world emoticon - smile.
To Enable the Debug mode:
1. Turn off your camera
2. Open the SD flash card door and leave it open
3. Turn on your camera. Now you should see the Debug Menu on your screen
4. Close the SD flash door
5. The menu stays on the screen. The first line of the Menu should read "Debug mode ". Use "->" button to toggle the Debug mode and to set it to Enable
6. Press "OK". Half pressing the shutter will have the "Debug mode" appear on the screen. Now you can have your fun with the AF corrections.
Please note, that if you switch the camera off and on, you will get back to the "Debug menu" again. You will also get back to this menu when the camera wakes up from the standby. Hitting "OK" will bring you back to the shooting mode with the "Debug mode" showing on your screen.
To Disable the "Debug mode" (all AF corrections are still stored in memory)
1. Switch off the camera
2. Turn the camera on
3. At the "Debug menu" use "->" button to disable the "Debug mode"
4. Press "OK" button. That's it. The "Debug mode" has gone. To Re-enable it, see above emoticon - smile.
Special thanks to the creator of the http://www.pentax-hack.info blog.
The method is based on the information published here:
http://www.pentax-hack.info/documents/blog.php?page=1
1. Use a notepad to create a file MODSET.TXT with the following line:
[OPEN_DEBUG_MENU]
followed by a new empty line.
2. Save the file on the root directory of your SD flash card (either use the USB cable to connect to the camera or an external SD flash reader).
Now you are ready to Enable/Disable the Debug mode on the best camera in the world emoticon - smile.
To Enable the Debug mode:
1. Turn off your camera
2. Open the SD flash card door and leave it open
3. Turn on your camera. Now you should see the Debug Menu on your screen
4. Close the SD flash door
5. The menu stays on the screen. The first line of the Menu should read "Debug mode ". Use "->" button to toggle the Debug mode and to set it to Enable
6. Press "OK". Half pressing the shutter will have the "Debug mode" appear on the screen. Now you can have your fun with the AF corrections.
Please note, that if you switch the camera off and on, you will get back to the "Debug menu" again. You will also get back to this menu when the camera wakes up from the standby. Hitting "OK" will bring you back to the shooting mode with the "Debug mode" showing on your screen.
To Disable the "Debug mode" (all AF corrections are still stored in memory)
1. Switch off the camera
2. Turn the camera on
3. At the "Debug menu" use "->" button to disable the "Debug mode"
4. Press "OK" button. That's it. The "Debug mode" has gone. To Re-enable it, see above emoticon - smile.
Special thanks to the creator of the http://www.pentax-hack.info blog.
Posted 23/05/2011 - 13:45
Link
I am no expert here but I think you may want to repeat this with a focus chart designed for the purpose. Most of these have a large black and white area in the centre in order to ensure that the focus point is actually in the middle of the scale. The problem with focussing on a single line is ensuring that the camera is focussing exactly where you want.
Even with single point focussing there is a bit of give as to where the focus point actually is. If the camera has focussed on a different line you may see it as front or back focus.
The camera also doesn't seem to be straight on (at least in the first shot) and therefore any tilt could affect the results.
Even with single point focussing there is a bit of give as to where the focus point actually is. If the camera has focussed on a different line you may see it as front or back focus.
The camera also doesn't seem to be straight on (at least in the first shot) and therefore any tilt could affect the results.
You will only prise my 43Ltd from my cold, dead hands...
Posted 23/05/2011 - 14:17
Link
WobblyGoblin wrote:
I am no expert here but I think you may want to repeat this with a focus chart designed for the purpose. Most of these have a large black and white area in the centre in order to ensure that the focus point is actually in the middle of the scale.
I know of two charts:I am no expert here but I think you may want to repeat this with a focus chart designed for the purpose. Most of these have a large black and white area in the centre in order to ensure that the focus point is actually in the middle of the scale.
One has the chart for mounting at 45 degrees, horizontal camera, and the focus point is a half black/half white oval (becomes a circle at 45 deg)
The other has the camera at 45 degrees, chart horizontal, and the focus point is a black line that measures 2.5 mm.
You can get the second from http://FocusTestChart.com (and note that it goes back several years).
Either will give results to 2mm intervals.
I think that your chart might be better if the black triangle had it's apex moved to the other side of the RH column to get better contrast for focussing.
Geoff
Water can wear away a stone - but it can't cook lunch
X-5
istDS
K2000
P50.
Lenses Digital: 50-200, 18-55 KAF: 28-80.
Lenses KA & K: SMC-KA f2.0, SMC-K f1.4, SMC-K f1.7 Tokina KA 28-70 , SMC Pentax 70-210 F4, Sigma KA 75-300 , Hanimex 500mm Mirror, and the Tamron Adaptall-2 stuff.
and then there's all the M42 kit, and the accessories ...
X-5
istDS
K2000
P50.
Lenses Digital: 50-200, 18-55 KAF: 28-80.
Lenses KA & K: SMC-KA f2.0, SMC-K f1.4, SMC-K f1.7 Tokina KA 28-70 , SMC Pentax 70-210 F4, Sigma KA 75-300 , Hanimex 500mm Mirror, and the Tamron Adaptall-2 stuff.
and then there's all the M42 kit, and the accessories ...
Posted 23/05/2011 - 15:11
Link
All points noted (not yet understood-but noted)
I used the large triangle to indicate the centre and focused with the selector set to point when the camera beeped with the small red square in the viewfinder on the centre line I fired the shutter.
Is that the right thing to do?
The camera was square to the board which was tilted back at 45 deg.
Camera was 1 metre away from centre of board
Small divisions are 1.414 separation ie 1mm in Horizontal plane
Lens appears to focus abot 20-30mm back
Bernard
I used the large triangle to indicate the centre and focused with the selector set to point when the camera beeped with the small red square in the viewfinder on the centre line I fired the shutter.
Is that the right thing to do?
The camera was square to the board which was tilted back at 45 deg.
Camera was 1 metre away from centre of board
Small divisions are 1.414 separation ie 1mm in Horizontal plane
Lens appears to focus abot 20-30mm back
Bernard
Posted 23/05/2011 - 16:52
Link
Ok - Downloaded Focus Test chart and redone experiment
I placed it further in the workshop to avooid the backlighting. Lighting on all is from a skylight.
[IMG]http://i1236.photobucket.com/albums/ff444/Frogherder/IMGP5892.jpg[/IMG]
Looks OK to me so I don't think I'll be fiddling in debug mode
(incidentally page 4 of the blog doesn't say " MODSET.TXT" it uses a numerical value rather than TXT and doesn't provide a number for a K10D with 1.31 software - or have I found the wrong info?)
regards
Bernard
I placed it further in the workshop to avooid the backlighting. Lighting on all is from a skylight.
[IMG]http://i1236.photobucket.com/albums/ff444/Frogherder/IMGP5892.jpg[/IMG]
Looks OK to me so I don't think I'll be fiddling in debug mode
(incidentally page 4 of the blog doesn't say " MODSET.TXT" it uses a numerical value rather than TXT and doesn't provide a number for a K10D with 1.31 software - or have I found the wrong info?)
regards
Bernard
Posted 23/05/2011 - 16:57
Link
Frogherder wrote:
All points noted (not yet understood-but noted)
I used the large triangle to indicate the centre and focused with the selector set to point when the camera beeped with the small red square in the viewfinder on the centre line I fired the shutter.
Is that the right thing to do?
The camera was square to the board which was tilted back at 45 deg.
Camera was 1 metre away from centre of board
Small divisions are 1.414 separation ie 1mm in Horizontal plane
Lens appears to focus abot 20-30mm back
Bernard
This guy has a good article about focus adjustment and explains the details much better than I can.All points noted (not yet understood-but noted)
I used the large triangle to indicate the centre and focused with the selector set to point when the camera beeped with the small red square in the viewfinder on the centre line I fired the shutter.
Is that the right thing to do?
The camera was square to the board which was tilted back at 45 deg.
Camera was 1 metre away from centre of board
Small divisions are 1.414 separation ie 1mm in Horizontal plane
Lens appears to focus abot 20-30mm back
Bernard
http://pentaxdslrs.blogspot.com/2008/05/af-adjustment-test-chart-specifically.ht...
I think your technique seems sound and you clearly know a lot more about geometry and engineering than me (the bit about 1.414 etc loses me although I think I understand the concept). It is just the part about the actual focus point which may cause an issue. My understanding is that the red square is an approximation of the focus point rather than gospel truth. Using big blocks of black and white means the camera can only focus where the two meet (i.e. where there is a contrast). If the camera is too high or too low it will "hunt" and not focus.
I've used the techniques of the guy above and was able to get some fairly consistent results.
Hope that helps.
You will only prise my 43Ltd from my cold, dead hands...
Posted 23/05/2011 - 17:02
Link
Thanks - I'll have a look at your link
So for every 1.414mm up a 45 deg slope you travel the vertial and horizontal distances are each 1mm
regards
Bernard
Quote:
(the bit about 1.414 etc loses me
It's simply the length of the diagonal of a square 1 x 1(the bit about 1.414 etc loses me
So for every 1.414mm up a 45 deg slope you travel the vertial and horizontal distances are each 1mm
regards
Bernard
Posted 23/05/2011 - 20:22
Link
Frogherder wrote:
(incidentally page 4 of the blog doesn't say " MODSET.TXT" it uses a numerical value rather than TXT and doesn't provide a number for a K10D with 1.31 software - or have I found the wrong info?)
regards
Bernard
I did it on the GX10, so can't say for sure what the file needs to be called on the K10D - but I'm fairly sure MODSET.TXT is actually correct.
(incidentally page 4 of the blog doesn't say " MODSET.TXT" it uses a numerical value rather than TXT and doesn't provide a number for a K10D with 1.31 software - or have I found the wrong info?)
regards
Bernard
Posted 23/05/2011 - 20:25
Link
Frogherder wrote:
Ok - Downloaded Focus Test chart and redone experiment
Looks OK to me so I don't think I'll be fiddling in debug mode
Looks good to me as well. Now, if you look at the pic that you posted, you will see that your test chart is not quite square to the camera. Look carefully, and the LH side is going out of focus before the right - nearer to you - with the reverse true for that part of the chart beyond the focus line. You have created a lovely example of why you have to be nit-picky careful with anything to do with optics (manufactured or human).Ok - Downloaded Focus Test chart and redone experiment
Looks OK to me so I don't think I'll be fiddling in debug mode
Geoff
Water can wear away a stone - but it can't cook lunch
X-5
istDS
K2000
P50.
Lenses Digital: 50-200, 18-55 KAF: 28-80.
Lenses KA & K: SMC-KA f2.0, SMC-K f1.4, SMC-K f1.7 Tokina KA 28-70 , SMC Pentax 70-210 F4, Sigma KA 75-300 , Hanimex 500mm Mirror, and the Tamron Adaptall-2 stuff.
and then there's all the M42 kit, and the accessories ...
X-5
istDS
K2000
P50.
Lenses Digital: 50-200, 18-55 KAF: 28-80.
Lenses KA & K: SMC-KA f2.0, SMC-K f1.4, SMC-K f1.7 Tokina KA 28-70 , SMC Pentax 70-210 F4, Sigma KA 75-300 , Hanimex 500mm Mirror, and the Tamron Adaptall-2 stuff.
and then there's all the M42 kit, and the accessories ...
Posted 23/05/2011 - 21:49
Link
WobblyGoblin wrote:
This guy has a good article about focus adjustment and explains the details much better than I can.
http://pentaxdslrs.blogspot.com/2008/05/af-adjustment-test-chart-specifically.ht...
Interesting that, even though the article is 3 years old and on his own blog, he failed to answer a criticism in the comments that said : The centre "target" is way too small with too many extraneous elements for the centre AF to lock on to.
This guy has a good article about focus adjustment and explains the details much better than I can.
http://pentaxdslrs.blogspot.com/2008/05/af-adjustment-test-chart-specifically.ht...
http://frogfish.smugmug.com/ Pentax. Pentax DA*300/4, Cosina 55/1.2, Lens Baby Composer Pro & Edge 80, AFA x1.7, Metz 50 af1.
Nikon. D800. D600. Sigma 500/4.5, Nikon 300/2.8 VRII, Sigma 120-300/2.8, Zeiss Distagon ZF2 21/2.8, Zeiss Distagon ZF2 35/2.0, Sigma 50/1.4, Nikkor 85/1.8, Nikon TC20EIII, Nikon TC14EII, Kenko x1.4, Sigma 2.0
Nikon. D800. D600. Sigma 500/4.5, Nikon 300/2.8 VRII, Sigma 120-300/2.8, Zeiss Distagon ZF2 21/2.8, Zeiss Distagon ZF2 35/2.0, Sigma 50/1.4, Nikkor 85/1.8, Nikon TC20EIII, Nikon TC14EII, Kenko x1.4, Sigma 2.0
Posted 24/05/2011 - 07:23
Link
Maybe linked to the wrong page... I downloaded 3 charts from his website with different size centres. You pick the one that suits the field of view of the lens.
You will only prise my 43Ltd from my cold, dead hands...
Posted 24/05/2011 - 18:00
Link
Having messed about with charts, including the one posted above, I've found it perfectly adequate to shoot various real world items around the house of garden to check AF accuracy. When I used the charts I always took loads of random test pics of various stuff to check in the real world anyway. print on sides of cans of beans and bottles etc are good subjects, or anything where you can shoot an angle and whether the lens is FFing or BFing
I've found from experience do not need to be uber accurate and getting stuff square on. I've also found that phase AF on cameras is not 100% consistent so always take a few shots.
I even made one of these a few months ago.
http://blog.david-kennedy.com/wp-content/uploads/2010/12/LA2-Prod-01-101124A-Blo...
I've found from experience do not need to be uber accurate and getting stuff square on. I've also found that phase AF on cameras is not 100% consistent so always take a few shots.
I even made one of these a few months ago.
http://blog.david-kennedy.com/wp-content/uploads/2010/12/LA2-Prod-01-101124A-Blo...
[i]Bodies: 1x K-5IIs, 2x K-5, Sony TX-5, Nokia 808
Lenses: Pentax DA 10-17mm ED(IF) Fish Eye, Pentax DA 14mm f/2.8, Sigma 17-70mm f/2.8, Pentax-A 28mm f/2.8, Sigma 30mm F1.4 EX DC, Pentax-A 50mm f/1.2, Pentax-A 50mm f/1.4, Pentax-FA 50mm f/1.4, Pentax-A 50mm f/1.7, Pentax DA* 50-135mm f/2.8, Sigma 135-400mm APO DG, and more ..
Flash: AF-540FGZ, Vivitar 283
Lenses: Pentax DA 10-17mm ED(IF) Fish Eye, Pentax DA 14mm f/2.8, Sigma 17-70mm f/2.8, Pentax-A 28mm f/2.8, Sigma 30mm F1.4 EX DC, Pentax-A 50mm f/1.2, Pentax-A 50mm f/1.4, Pentax-FA 50mm f/1.4, Pentax-A 50mm f/1.7, Pentax DA* 50-135mm f/2.8, Sigma 135-400mm APO DG, and more ..
Flash: AF-540FGZ, Vivitar 283
Posted 24/05/2011 - 18:57
Link
[i]Bodies: 1x K-5IIs, 2x K-5, Sony TX-5, Nokia 808
Lenses: Pentax DA 10-17mm ED(IF) Fish Eye, Pentax DA 14mm f/2.8, Sigma 17-70mm f/2.8, Pentax-A 28mm f/2.8, Sigma 30mm F1.4 EX DC, Pentax-A 50mm f/1.2, Pentax-A 50mm f/1.4, Pentax-FA 50mm f/1.4, Pentax-A 50mm f/1.7, Pentax DA* 50-135mm f/2.8, Sigma 135-400mm APO DG, and more ..
Flash: AF-540FGZ, Vivitar 283
Lenses: Pentax DA 10-17mm ED(IF) Fish Eye, Pentax DA 14mm f/2.8, Sigma 17-70mm f/2.8, Pentax-A 28mm f/2.8, Sigma 30mm F1.4 EX DC, Pentax-A 50mm f/1.2, Pentax-A 50mm f/1.4, Pentax-FA 50mm f/1.4, Pentax-A 50mm f/1.7, Pentax DA* 50-135mm f/2.8, Sigma 135-400mm APO DG, and more ..
Flash: AF-540FGZ, Vivitar 283
Add Comment
To leave a comment - Log in to Pentax User or create a new account.



1776 posts
17 years
Burton upon Trent
Having read a few recent threads on the subject of adjusting the AF of a lens I thought I'd test my K10D 18-55mm lens.
I drew a scale with Autocad and printed it at 1.414 times on A4 paper. This was then stuck down with masking tape to a piece of timber supported at 45 degrees.
The camera mounted on a tripod was set at the same height as the black triangle and the lens autofucused on the central line.
It appears my lens focuses further away.
These two images 1-camera in portrait & 2-landscape show the results :-
[IMG]http://i1236.photobucket.com/albums/ff444/Frogherder/IMGP5889.jpg[/IMG]
[IMG]http://i1236.photobucket.com/albums/ff444/Frogherder/IMGP5890.jpg[/IMG]
All I have to do now is find out ou to adjust the lens - any comments welcome.
If anyone would like a copy of the scale in PDF format send me a PM
regards
Bernard
edit,
The original pics did not show moire patterns - how do I get rid of these for posting purposes?