Cable release for K5

Frogherder
Posted 18/01/2012 - 17:21 Link
Hi All,

Is the cable release for the K5 the same as that for the K10D.

I have a homemade one which provides focus and shutter via a small twin+earth jack plug

I also have a commercial one which provides timed/delay timed shutter release.

When I tried them on the K5 the focus didn't operate although the shutter did.

Bernard
Algernon
Posted 18/01/2012 - 17:48 Link
There's probably a setting in the camera menu to allow
AF with a remote, similar to the K20D
Half Man... Half Pentax ... Half Cucumber

Pentax K-1 + K-5 and some other stuff

Algi
Frogherder
Posted 18/01/2012 - 18:08 Link
There is [C-18] and it's set to 2.

I have an IR remote which works correctly with this set, but not when set to 1.

I was wanting to use the digital timer remote to set up a series of shots, and whilst I can manually focus or use the AF button to do what I want I noticed the cable remote(s) wouldn't invoke a focus which suggests (to me at least) that maybe the pinouts are different, hence the question.

Bernard
Edited by Frogherder: 18/01/2012 - 18:08
Gwyn
Posted 18/01/2012 - 20:55 Link
I just tried my cable release in my K-5 and it auto-focusses just fine. I have a JJC which was meant for a Canon.
Algernon
Posted 18/01/2012 - 21:01 Link
Check the plug is wired like this:

http://www.doc-diy.net/photo/remote_pinout/

I'm offline now until tomorrow
Half Man... Half Pentax ... Half Cucumber

Pentax K-1 + K-5 and some other stuff

Algi
Algernon
Posted 19/01/2012 - 09:10 Link
Just checked mine with the Pentax "CS-205 Cable Switch For Remote Shutter Release" and it focused first.... no problems.

Camera was on:
M exposure
NO SR (on tripod so I switched it off)
AF-S (GREEN)
Half Man... Half Pentax ... Half Cucumber

Pentax K-1 + K-5 and some other stuff

Algi
Frogherder
Posted 19/01/2012 - 13:50 Link
Thanks all

Problem solved -

Both releases had a wire loose to the focusing
The plug end on the home built one
The switch connection on the commercial one.

And to cap it all I found the wire into one of the probes of my multimeter is intermittent.

What are the odds of that?

So soldering iron out and repairs done. Note to self - check thoroughly next time.
At least I didn't take the camera apart, then discover a loose wire in the multimeter.


Anyway thanks for checking. I didn't want to mess up my new camera, if the pin outs had have been different.


Regards
Bernard
Edited by Frogherder: 19/01/2012 - 13:51
Frogherder
Posted 19/01/2012 - 16:34 Link
Algernon wrote:
Check the plug is wired like this:

http://www.doc-diy.net/photo/remote_pinout/

I'm offline now until tomorrow
Algi,

A most interesting site.
I rather like the multi-function trigger device based around the ATmega88V but have no facilties for programming it

regards
Bernard
Algernon
Posted 19/01/2012 - 16:57 Link
Glad to hear it was easy to sort out.

There is some interesting stuff on that site
Half Man... Half Pentax ... Half Cucumber

Pentax K-1 + K-5 and some other stuff

Algi

Add Comment

To leave a comment - Log in to Pentax User or create a new account.



Proudly supporting Pentax User

Samsung Logo Asahi Pentax Logo